Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
06-26-2001, 06:55 AM
|
#1 |
|
Registered Member
Join Date: Mar 1999
Location: Sanford NC USA
Posts: 155
|
5000 miles on new motor ready to turn on the JUICE
i was wondering what kinda shot i should break my motor in on. my mods are below.. i am thinking a hundred shot but any ideas are great..Remember street car~
------------------ SOLD THE 87GT, .. GT40, 70mmTB, 75mmBullet, 24lbinjectors, cold air induction, Edelbrok 6025 Rpm's, Inch phonolic spacer, tall FMSvalve covers, an SFI balancer, Canton 7quart, the shortblock... Lunati 51025 (224/232 .535/. 544 @112 deg) Ross lightweight pistons (10:1) Eagle H-Beams, Total Seal plasma Moly Rings, Clevite bearings, ARP throughout, FMS main Girdle&Studs, Forged Crank, of course HV-OilPump and hardened FMS shaft, Dual Friction centerforce, T5, and 4.10's Longtubes and 2.25 tail pi |
|
|
|
06-27-2001, 10:07 PM
|
#2 |
|
Registered Member
Join Date: Sep 1998
Posts: 495
|
It would take me 5 years to rack up 5000 miles. I would run as much as I intended right off. Just make sure its gonna work. Back in the day, guys were spraying stock motors practically off the show room floor.
|
|
|
|
|
06-27-2001, 10:34 PM
|
#3 |
|
Registered Member
Join Date: Apr 2000
Location: middleburg, fl, usa
Posts: 1,134
|
I would start off with a 75 shot until you get it tuned and running right and then step up to a 100 or a 150 shot.
------------------ James Cox nochevy@hotmail.com 1991 Mustang LX 12.565 @109.38mph 1.764 60ft |
|
|
|
|
06-29-2001, 11:43 AM
|
#4 |
|
Registered Member
Join Date: Mar 1999
Location: Sanford NC USA
Posts: 155
|
thanx guys it took me only a few months like 3.5 maybe to get 5000 miles on her its my daily driver thats why.. thats what i will do 75 then 100
------------------ SOLD THE 87GT, .. GT40, 70mmTB, 75mmBullet, 24lbinjectors, cold air induction, Edelbrok 6025 Rpm's, Inch phonolic spacer, tall FMSvalve covers, an SFI balancer, Canton 7quart, the shortblock... Lunati 51025 (224/232 .535/. 544 @112 deg) Ross lightweight pistons (10:1) Eagle H-Beams, Total Seal plasma Moly Rings, Clevite bearings, ARP throughout, FMS main Girdle&Studs, Forged Crank, of course HV-OilPump and hardened FMS shaft, Dual Friction centerforce, T5, and 4.10's Longtubes and 2.25 tail pi |
|
|
|
|
06-29-2001, 04:20 PM
|
#5 |
|
Guest
Posts: n/a
|
Hey guys....nitrous illeterate here.....what do yo mean by "tuned in"??? Thanks.
------------------ '90 LX 5.0; 12K original miles (no sh*&); 3.55 gears; pulleys;Edelbrock Performer Heads; BBK shorties; MSD 6AL box w/ blaster 2 coil; Motorsport E303 cam; Pro-M 75mm MAF; BBK 70mm TB; Eibach spring kit; Southside welded subs; K&N cone filter charger; Hurst shifter; fiberglass turbo hood; A/C-less; rear seat-less; cat-less; 2 chamber Flos; Corbeau racing seats (fronts); 30# injectors; JMS Chip; 190 lb fp; TFS track heat Intake (12.299 @ 113) |
|
|
|
06-29-2001, 11:51 PM
|
#6 |
|
Registered Member
Join Date: Apr 2000
Location: middleburg, fl, usa
Posts: 1,134
|
Making sure that he has no detonation or problems with fuel before he goes to a bigger shot, because 75 is a lot more forgiving than a 100 through 150 would be.
Just a safety precaution. ------------------ James Cox nochevy@hotmail.com 1991 Mustang LX 12.565 @109.38mph 1.764 60ft |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Too many miles for the Juice??? | Blaster | Windsor Power | 2 | 07-12-2004 11:33 PM |
| turn signal-maybe the whole harness-calling all electricians? | rwhite65 | Classic Mustangs | 6 | 07-25-2003 08:40 AM |
| Nuclear explosion effects.... | silver_pilate | Blue Oval Lounge | 13 | 11-22-2002 11:41 AM |