Hopefully the last question on heads..

SlowStang2 · 07-11-2001, 03:39 PM

O.k. the day is coming near for the heads purchase. Gotta clarify a few things to make sure I screw up. On trick flows twisted wedges there are 2. One for stud mount rockers and one for stud mount rockers w/O-ring groove. Which one do i need? My car is a 94 stock block, so which way do I steer? I know with these heads, I have to buy additional parts(you know, pushrods and extruded rockers[saw it in Summit]) which makes them a bit more than Edeleborck's IF edel's don't need any more parts. Do Edel's need additional parts to bolt them on? Thanx again...Oh yea speaking of Edelbrock, anyone try the inertia shocks?

------------------
94' Stang GT Convertible Cobra upper&lower, Mac cold air w/K&N, BBK equal length shorties, BBK offroad H-pipe, American Thunder cat-back, BBK T/B 65mm, 24lb injectors, Pro-77mm MAM, pulleys, aluminum driveshaft, 3.55s 14.4@100. (Sad, i know. i have stock heads)

mufflerboy · 07-11-2001, 04:35 PM

My edelbrock heads needed nothing you can reuse your rockers and pushrods I opted to get roller rockers and bought new pushrods cause there cheap and its just cheap insurance that your not putting in a bent one.

------------------
93 coupe,373's ripper shifter,MAC 1-5/8 equal lengths,MAC 2-1/2" H-pipe with cats,flowmaster 2 chambers,lowered 1-1/2" with BBK springs.Motorsport HD clutch,,FMS pullies,75mm bullet maf,walbro 190 lph fuel pump,kirban adj fpr.edelbrock 6037's e303, cobra intake
frpp 1.6 roller rockers
mac cold air kit msd 6al
3" cowl hood factory five upper and lower control arms wms subframe connecter and strut tower brace
12.81@ 105.1 1.66 60ft

07-11-2001, 03:39 PM	#1
SlowStang2 Registered Member Join Date: May 2001 Location: Stuart, FL, US Posts: 147	Hopefully the last question on heads.. O.k. the day is coming near for the heads purchase. Gotta clarify a few things to make sure I screw up. On trick flows twisted wedges there are 2. One for stud mount rockers and one for stud mount rockers w/O-ring groove. Which one do i need? My car is a 94 stock block, so which way do I steer? I know with these heads, I have to buy additional parts(you know, pushrods and extruded rockers[saw it in Summit]) which makes them a bit more than Edeleborck's IF edel's don't need any more parts. Do Edel's need additional parts to bolt them on? Thanx again...Oh yea speaking of Edelbrock, anyone try the inertia shocks? ------------------ 94' Stang GT Convertible Cobra upper&lower, Mac cold air w/K&N, BBK equal length shorties, BBK offroad H-pipe, American Thunder cat-back, BBK T/B 65mm, 24lb injectors, Pro-77mm MAM, pulleys, aluminum driveshaft, 3.55s 14.4@100. (Sad, i know. i have stock heads)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GT-40X heads ?	Mustang_289	Windsor Power	9	09-30-2003 08:21 AM
New Heads. Any Tips	66StangGuy	Classic Mustangs	5	09-15-2003 08:20 PM
question on EDEL heads ...6022	vande97	Windsor Power	3	02-16-2002 03:19 PM
Heads and Cam....tough question	cyberstang5.0	Windsor Power	2	12-07-2001 09:22 AM
A general question about heads!	Thad	Windsor Power	0	10-10-2001 11:17 AM

07-11-2001, 04:35 PM	#2
mufflerboy Registered Member Join Date: Jan 1999 Posts: 126	My edelbrock heads needed nothing you can reuse your rockers and pushrods I opted to get roller rockers and bought new pushrods cause there cheap and its just cheap insurance that your not putting in a bent one. ------------------ 93 coupe,373's ripper shifter,MAC 1-5/8 equal lengths,MAC 2-1/2" H-pipe with cats,flowmaster 2 chambers,lowered 1-1/2" with BBK springs.Motorsport HD clutch,,FMS pullies,75mm bullet maf,walbro 190 lph fuel pump,kirban adj fpr.edelbrock 6037's e303, cobra intake frpp 1.6 roller rockers mac cold air kit msd 6al 3" cowl hood factory five upper and lower control arms wms subframe connecter and strut tower brace 12.81@ 105.1 1.66 60ft