Shifter T-handle

Stefan · 10-03-1999, 08:37 AM

Hey guys. This might seem fairly obvious, but I thought I would ask before digging in. I have a 66 coupe with an automatic (no console)that I just purchased a shifter bezel and T-handle for. The bezel is a no brainer but I was wondering about the handle. Is there some correct procedure for removing the old and installing the new one? I have never looked at anything but exploded diagrams in catalogs that don't tell me much. I guess this is all basically in reference to the cable and button setup. Thanks in advance for any help as I thought I would ask before tearing in.

Stefan

------------------
66 Standard coupe
200 inline 6 - Pertronix ignition, K&N, Clifford Perf. 6 into 2 headers(not installed yet), Holly carb

96 GT Convertible
K&N (more to come)

red · 10-04-1999, 02:03 AM

Shifter is just as easy as the bezel. Just remove the set screw and lift up and tword the drivers side (if I remember correctly).
-JON

Stefan · 10-04-1999, 04:15 AM

Thanks for the info. I'm gonna dig in when it stops raining.
Stefan

------------------
66 Standard coupe
200 inline 6 - Pertronix ignition, K&N, Clifford Perf. 6 into 2 headers(not installed yet), Holly carb

96 GT Convertible
K&N (more to come)

10-03-1999, 08:37 AM	#1
Stefan Registered Member Join Date: Dec 1998 Location: Manhattan, KS 66502 Posts: 599	Shifter T-handle Hey guys. This might seem fairly obvious, but I thought I would ask before digging in. I have a 66 coupe with an automatic (no console)that I just purchased a shifter bezel and T-handle for. The bezel is a no brainer but I was wondering about the handle. Is there some correct procedure for removing the old and installing the new one? I have never looked at anything but exploded diagrams in catalogs that don't tell me much. I guess this is all basically in reference to the cable and button setup. Thanks in advance for any help as I thought I would ask before tearing in. Stefan ------------------ 66 Standard coupe 200 inline 6 - Pertronix ignition, K&N, Clifford Perf. 6 into 2 headers(not installed yet), Holly carb 96 GT Convertible K&N (more to come)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Different shifter handle?	Jaegermeister2k	Modular Madness	12	10-27-2003 06:23 PM
aod shifter handle swap?	sockmonkey	Windsor Power	2	08-06-2001 01:05 PM
will steeda tri-ax handle fit on my hurst short throw shifter?	SHaFT7	Windsor Power	1	06-10-2001 03:10 PM
Vibrating shifter handle, grinding	bark3rd	Modular Madness	9	05-18-2001 09:54 AM
Installed the MGW Ltd. shifter handle...got pics===>	T_Bone	Modular Madness	5	05-13-2001 03:53 AM

10-04-1999, 02:03 AM	#2
red Registered Member Join Date: Sep 1998 Location: Millburn, NJ Posts: 310	Shifter is just as easy as the bezel. Just remove the set screw and lift up and tword the drivers side (if I remember correctly). -JON

10-04-1999, 04:15 AM	#3
Stefan Registered Member Join Date: Dec 1998 Location: Manhattan, KS 66502 Posts: 599	Thanks for the info. I'm gonna dig in when it stops raining. Stefan ------------------ 66 Standard coupe 200 inline 6 - Pertronix ignition, K&N, Clifford Perf. 6 into 2 headers(not installed yet), Holly carb 96 GT Convertible K&N (more to come)