![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Jul 2001
Location: SD/Murrieta
Posts: 20
|
![]() I'm running a C4 tranny with 3.55 gears, i want better freeway rpms so I'm converting to an overdrive. My friend's brother has a overdrive with a computer he was gonna stick in his 66. Now my question is, what is the computer for(shift electricly?) and how much harder will it be to install. Also, he is selling it all for $600, is that too much?
I know i dont have many details, but i wanna know what im gettin into before i get too deep. Any info is helpful on converting to an overdrive. Thanks ------------------ 68 fastback modified 289, C4, 3.55 gears, 2 chamber flomaster, GT look-a-like, lowered, blue head lights, blue blinkers, blue side makers, blue turn indicaters on hood, blue interior lights, blue map lights, blue liscense plate light, blue back-up lights(rewired the blink with the blinkers), blue alarm light, and blue strobe light attached to the front 1 1/8" sway bar |
![]() |
![]() |
![]() |
#2 |
Factoy Five Roadster
Join Date: May 2000
Location: Sevier Co,Tennessee
Posts: 1,681
|
![]() It is a easy swap to a AOD.
http://www.windsor-fox.com for the cross member and yoke and what ever else you need. Always remember to re-balance the AOD flex plate to 28.2 oz<thats what older motors need) The AOD plate is 50. oz's. Your motor will vibrate very bad and the rear bearings will fail if you dont. The best AOD's are 89-93's. These years have all of the revisions making them better than the others. I just picked up a 92 AOD w/converter and shifter etc, for $200.00, of course used. I usually pick up a core for about $150.00-250.00 from the yard. A couple of hundred dollars later and its new again. $600.00 is steep for a used trans, unless it has been rebuilt recently with performance parts. Get the converter with it !! Hope this helps any. ![]() |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Sep 1998
Location: Oviedo, FL
Posts: 992
|
![]() You can bolt up an AOD to your car with very little problem. I did it to my 68 FB. If it has an ECM, and it is FORD it is probably an AODE. This trans. needs an ECM to operate. It controls all the shifting.
|
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Jul 2001
Location: SD/Murrieta
Posts: 20
|
![]() the trans is rebuilt, thats about all i know right now...so this one is probably the AODE since its supposed to shirt electroniclly..another question, how much horsepower can it handle? Workin on an engine that should run 350-400...that should be ok, right? thanks again guys
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Sep 1998
Location: Oviedo, FL
Posts: 992
|
![]() It should handle that HP. Unless you are a Banzi driver and have your foot in it all the time.
Weak points, stock the is, are the O/D band and the two piece input shaft. But, if memory serves me, I think the AODE already has the 2 inch O/D band. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Electronic Overdrive | StangGT02 | Modular Madness | 1 | 05-27-2003 04:05 PM |
2.80's--4.11's gas milage? | 66StangGuy | Classic Mustangs | 24 | 08-19-2002 10:39 AM |
Is my overdrive out? | slag | Small Ponies | 0 | 03-13-2002 07:54 PM |
aod no overdrive | delrrex | Windsor Power | 7 | 03-12-2002 10:08 AM |
LenTech, Won't stay out of overdrive | bob_nj | Blue Oval Lounge | 2 | 03-05-2001 08:43 PM |