Shelby Intake

Brian Browning · 11-20-2000, 12:06 PM

Good morning,
The car I just bought does not have the original engine. Its got a 66 Hi Po. It also has a Shelby intake manifold and valve covers. I haven't seen this intake anywhere else (catalogs etc.). Is it worth anything? Also does anybody have a feeling for how it performs vs. a new Eldebrock or something. It does look cool, needs cleaned up though.

------------------
65 convertible
289 Hi Po
4 speed

red · 11-20-2000, 06:55 PM

I know Tony Branda makes a repop of this manifold. I'm not sure what it's worth but if it is original it must be worth a few hundred bucks.

Mercury · 11-21-2000, 01:08 AM

I've seen original shelby intakes go for an average of $450.

------------------
64 1/2 Red Mustang Coupe. 289, C4, 3:1 rear gear. Mallory duel point. Ported & Polished 65 heads shaved .01 with 351 windsor valves, high side of 10.5:1 comp, 1.7:1 sled rockers, blue wolverine lumpy cam, autolite 4100 Hipo 4 barrel. And to many others to list

2000 Perf Red Mustang GT. 5spd.

64 1/2 red 6cyl coupe. Auto. project car.

Brian Browning · 11-21-2000, 08:38 AM

Thanks guys,
About what I figured. Not enough to take it off and sell it, but it does add some to the coolness factor. Just got insurance and put her on the road yesterday!

------------------
65 convertible
289 Hi Po
4 speed

Brian Browning · 11-21-2000, 09:31 AM

I looked at the Branda site. There are pictures that look close, but where they say "COBRA" on the intake, mine says "SHELBY"
anybody have an idea what the heck this thing came off of?

macx · 11-23-2000, 09:02 AM

very probably was an over-counter add-onn like any other aftermarket manifold. I remember reading a comparison quite a few years ago that included the then-available 4bbl aftermarket intakes, I think this was maybe even before the Performer line came out. Before Performer, Edelbrock still had some really good 4bbl intakes, just not a catchy name for them. Anyway, the Shelby performed quite well against the others if I recall. You'd likely gain VERY few hp by swapping, and you've got a really cool piece there! Use it and be proud!

Brian Browning · 11-27-2000, 08:11 AM

Thank Macx,
I think I'll do exactly that. Its going to takesome cleanup before I'd be proud to have the car setting with the hood open, but I'll get there.

11-20-2000, 12:06 PM	#1
Brian Browning Registered Member Join Date: Sep 2000 Location: Hattiesburg, MS, USA Posts: 86	Shelby Intake Good morning, The car I just bought does not have the original engine. Its got a 66 Hi Po. It also has a Shelby intake manifold and valve covers. I haven't seen this intake anywhere else (catalogs etc.). Is it worth anything? Also does anybody have a feeling for how it performs vs. a new Eldebrock or something. It does look cool, needs cleaned up though. ------------------ 65 convertible 289 Hi Po 4 speed

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Trick Flow intake problems	shacar87	Windsor Power	9	11-14-2003 05:53 PM
Explore intake???????????	William Bowers	Windsor Power	2	02-14-2002 10:27 PM
HELP!!! oil in intake, what to do??	bosco	Windsor Power	4	02-03-2002 05:02 PM
OIL IN INTAKE almost sure from 'pcv'	QUIN	Windsor Power	8	03-09-2001 01:58 PM
Is the true about Edelbrock heads with TFS intake?	gt93mustang	Windsor Power	14	03-06-2001 07:01 PM

11-20-2000, 06:55 PM	#2
red Registered Member Join Date: Sep 1998 Location: Millburn, NJ Posts: 310	I know Tony Branda makes a repop of this manifold. I'm not sure what it's worth but if it is original it must be worth a few hundred bucks.

11-21-2000, 01:08 AM	#3
Mercury The Redneck James Bond Join Date: Sep 2000 Location: Fayetteville NC Posts: 1,707	I've seen original shelby intakes go for an average of $450. ------------------ 64 1/2 Red Mustang Coupe. 289, C4, 3:1 rear gear. Mallory duel point. Ported & Polished 65 heads shaved .01 with 351 windsor valves, high side of 10.5:1 comp, 1.7:1 sled rockers, blue wolverine lumpy cam, autolite 4100 Hipo 4 barrel. And to many others to list 2000 Perf Red Mustang GT. 5spd. 64 1/2 red 6cyl coupe. Auto. project car.

11-21-2000, 08:38 AM	#4
Brian Browning Registered Member Join Date: Sep 2000 Location: Hattiesburg, MS, USA Posts: 86	Thanks guys, About what I figured. Not enough to take it off and sell it, but it does add some to the coolness factor. Just got insurance and put her on the road yesterday! ------------------ 65 convertible 289 Hi Po 4 speed

11-21-2000, 09:31 AM	#5
Brian Browning Registered Member Join Date: Sep 2000 Location: Hattiesburg, MS, USA Posts: 86	I looked at the Branda site. There are pictures that look close, but where they say "COBRA" on the intake, mine says "SHELBY" anybody have an idea what the heck this thing came off of?

11-23-2000, 09:02 AM	#6
macx Registered Member Join Date: Oct 1999 Location: Gordonville MO USA Posts: 448	very probably was an over-counter add-onn like any other aftermarket manifold. I remember reading a comparison quite a few years ago that included the then-available 4bbl aftermarket intakes, I think this was maybe even before the Performer line came out. Before Performer, Edelbrock still had some really good 4bbl intakes, just not a catchy name for them. Anyway, the Shelby performed quite well against the others if I recall. You'd likely gain VERY few hp by swapping, and you've got a really cool piece there! Use it and be proud!

11-27-2000, 08:11 AM	#7
Brian Browning Registered Member Join Date: Sep 2000 Location: Hattiesburg, MS, USA Posts: 86	Thank Macx, I think I'll do exactly that. Its going to takesome cleanup before I'd be proud to have the car setting with the hood open, but I'll get there.