MustangWorks.com : Ford Forums - View Single Post

Childs · 12-16-2004, 06:56 PM

Info: 69 FB 302 2bbl Holley 4412 carb dual point dist

I working on my uncle's 69 fastback and its a mess. Nothing on it is stock, so the repair manuals are of little use. I got it running for a bit, then another uncle wanted to check the timing and he fooled with the distributer position and it would not start again. He then pulled out the distributer and supposedly realigned it, and now I'm thinking we're screwed. I turned the crank manually, and aligned up TDC with piston 1, and made sure each revolution (according to the rotor) matched up with TDC, but it still won't fire. I'm getting spark, but its only once in awhile when the spark tester is hooked up to piston 1. Its a dual point distributor, so I don't know if this is the correct behavior or not. It has a Holley 4412 2bbl carb, and there is fuel in the bowl so I'm thinking fuel wise its fine. Replaced the points and condenser, distributer wire, cap, rotor, ignition coil, and even the starter solenoid and voltage regulator.

Now, I'm thinking its just so out of whack timing wise that its not going to fire reliably. Is there anything I can do to make sure the timing is correct when the car won't start? I have the Haynes, Chilton, and Factory manual, and they only deal with timing when the car runs.

Also, the ignition coil measures about 5.6V when "-" is grounded and "+" is going straight to the battery. I've read that it should be 7-11v. The original coil, replaced coil, and brand new coil all read about 5.6v, so I'm wondering since the distributer isn't stock I need a special coil or something? When its normally hooked up, I have ignition running to "+", distributer wire and tach wire running to "-", and I noticed something with the test light. Test light lights up bright without distributer wire and tach connected to "-", but when they are its noticeably dimmer. Could this be an issue too?

12-16-2004, 06:56 PM	#1
Childs Registered Member Join Date: Dec 2004 Posts: 8	Need help, 69 wont start Info: 69 FB 302 2bbl Holley 4412 carb dual point dist I working on my uncle's 69 fastback and its a mess. Nothing on it is stock, so the repair manuals are of little use. I got it running for a bit, then another uncle wanted to check the timing and he fooled with the distributer position and it would not start again. He then pulled out the distributer and supposedly realigned it, and now I'm thinking we're screwed. I turned the crank manually, and aligned up TDC with piston 1, and made sure each revolution (according to the rotor) matched up with TDC, but it still won't fire. I'm getting spark, but its only once in awhile when the spark tester is hooked up to piston 1. Its a dual point distributor, so I don't know if this is the correct behavior or not. It has a Holley 4412 2bbl carb, and there is fuel in the bowl so I'm thinking fuel wise its fine. Replaced the points and condenser, distributer wire, cap, rotor, ignition coil, and even the starter solenoid and voltage regulator. Now, I'm thinking its just so out of whack timing wise that its not going to fire reliably. Is there anything I can do to make sure the timing is correct when the car won't start? I have the Haynes, Chilton, and Factory manual, and they only deal with timing when the car runs. Also, the ignition coil measures about 5.6V when "-" is grounded and "+" is going straight to the battery. I've read that it should be 7-11v. The original coil, replaced coil, and brand new coil all read about 5.6v, so I'm wondering since the distributer isn't stock I need a special coil or something? When its normally hooked up, I have ignition running to "+", distributer wire and tach wire running to "-", and I noticed something with the test light. Test light lights up bright without distributer wire and tach connected to "-", but when they are its noticeably dimmer. Could this be an issue too?