MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Racing > Racer's Club House
Register FAQ Members List Calendar

Notices


 
 
Thread Tools Rate Thread Display Modes
Prev Previous Post   Next Post Next
Old 07-14-2002, 10:06 AM   #1
Fox Body
Mustang Maniac
 
Fox Body's Avatar
 
Join Date: Sep 2000
Location: GA, U.S.A
Posts: 2,266
Question Roll cage install ...a few questions

Jeff (or whoever else can answer this ?),

I checked out your website (very helpful) on the roll cage tech article. I have 4-points successfully TIG welded in, but have the 2 side bars I need to cut and get welded. In your article it seems as if the 6x6x1/8" steel plates are welded to the floor. In the NHRA rulebook it shows the bars welded to the plates and the plates bolted to the floor with a plate on top and bottom of floor (bolted to each other with 4 3/8" bolts). Maybe these are 2 optional paths. The bolt method was the path I chose (I guess), but S&W only gave me 6 plates. If I have to do top and bottom at 6 points on teh floor, then obviously I need 12 plates. A friend of mine is cutting me some more plates to finish the job, but what do you think? I don't see any of this little details in the NHRA book.

So should the plates be welded to the floor (MIG or TIG, if yes). I think I would like to go ahead and get the other plates and continue bolting it all in. I just need some guidance here.

Also, I need to start painting the cage. I saw you used a certain time of frame paint, but did you use any primer and did you do any sanding prior to painting r did you just clean the cage of dirt and spray it?

Thanks.
__________________
351W-powered 1979 Ford Mustang Ghia notchback
'79 Video @ Idle
Stock 5.8L under 4" cowl 'glass hood, C4 w/ Transgo shift kit, Holley 750 cfm, Edelbrock Performer RPM intake; Fluidyne Al radiator, Flexalite 175 electric fan, 1 5/8" MAC shorty headers, FRPP Al driveshaft; S&W 6-point cage; 2.5" Off road H-pipe, 2-chamber Flowmasters, 8.8" Rear w/ 3.55s; Weld wheels (15x6;15x8), Front: 225/60/15, Rear: 275/50/15 Nitto NT 555R Drag Radials;
14 x 4” K&N X-stream air filter.


'92 GT (5-speed)
Small In Car Video
Stock 5.0L, 2-chamber Flowmasters, MAC CAI, Tri-Ax, Al pedals...

"Red, thou art my companion. Hasten now your quickened metamorphosis to Green that I may conquer all who dare abide there beside me. May they be left thither behind burnt black." ---Fox Body
Fox Body is offline   Reply With Quote
 



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Roll cage questions MJ86GT Corner Carvers Delight 1 11-12-2003 04:41 PM
Questions on Roll Cages, Welding, and Ignition BlackFireN2O Windsor Power 3 08-25-2002 08:01 AM
how much to install a roll cage? 82 GT Windsor Power 15 04-04-2002 03:34 PM
Gathering info on roll cage installation. Fox Body Windsor Power 5 02-25-2002 11:35 PM
roll cage install... ed1371 Windsor Power 4 03-19-2001 11:17 AM


All times are GMT -5. The time now is 06:53 PM.


SEARCH