'00GT vs. Mach I

blue00gt · 11-12-2003, 08:19 PM

Raced some kid in a new blue Mach I from about a 60mph roll on the freeway. I had a 260lb passenger and he was by himself. I dropped it into 3rd and stomped it and we were pretty much even all the way through 4th up to about 105 where I let off because I could see some cars up ahead. I thought I would get pulled on a little from a roll but it didn't happen.
I wish the track was still open. I have surprised myself with the cars I hang with or beat since I got the 4.10s. I don't think I'm making more than 285 or so at the crank, but she runs about even with low-13 second cars on street tires if I get a good launch.

fastang · 11-12-2003, 09:42 PM

SWEET! What kinda rpms are you turnin with those gears? Is first gear useless or hard to launch well with?

blue00gt · 11-13-2003, 03:28 PM

I'm turning about 2500 rpm at 70mph with a 5-speed and 285/40-17's out back. First gear is definitely trickier now, but if I just slip the clutch off the line and let it out just right as it gets rolling and I floor it I don't usually break traction as long as the road is smooth. If the road is not good it will spin them no matter what at the top of 1st. I have to shift a hair slower into 2nd on street tires or it will roast them good, but once I got used to it I am stomping other cars out of the hole.
I also have stiffer springs than most folks run on the street, so if I can launch with 4.10s then anyone should be able to with practice. In front I have 350 lb/in coilovers, which is the equivalent of 1250 lb/in in the stock position. Out back I have 450 lb/in springs in the stock location with a torque arm and panhard bar. I'm sure if I ran softer springs it would be much easier to launch.

Fox Body · 11-13-2003, 06:24 PM

blue00gt, I gotta say, man, I've always loved how your car looks from the first time I saw it. Really like what you done to it, not much, but just enough (and also the color). Good race, BTW. Any other plans for the car in terms of engine or exhaust mods?

fastang · 11-13-2003, 08:40 PM

Thanks for clueing me in. I think Im gonna go with 373's though. I dont want to be turning 3 grand or more at 75-80 mph.

blue00gt · 11-13-2003, 08:42 PM

Thanks, Fox Body.
As far as what's next for the stang, I have a Spec Stage II clutch, aluminum flywheel, and aluminum driveshaft that just need to be installed.
After that I plan on saving up some money and getting the Kenne Belle twin screw 8psi intercooled kit early next year.
The only thing left on my plan to buy after that is a roll cage, 5-point harnesses, rear seat delete, and Baer 12" rear brake kit.
At that point I should have the full package as far as handling, braking, acceleration, and appearance. Nothing else to buy except what I break with the extra horsepower (maybe a T56 when the T45 dies).

EZRIDN · 11-14-2003, 10:38 AM

Sweet run!

Fox Body · 11-14-2003, 03:37 PM

Quote:

Originally posted by blue00gt
Thanks, Fox Body.
As far as what's next for the stang, I have a Spec Stage II clutch, aluminum flywheel, and aluminum driveshaft that just need to be installed.
After that I plan on saving up some money and getting the Kenne Belle twin screw 8psi intercooled kit early next year.
The only thing left on my plan to buy after that is a roll cage, 5-point harnesses, rear seat delete, and Baer 12" rear brake kit.
At that point I should have the full package as far as handling, braking, acceleration, and appearance. Nothing else to buy except what I break with the extra horsepower (maybe a T56 when the T45 dies).

Cool.

IF I had to do it all over again (and had more money than the first time), I'd go with one of those lighter chromoly cages that have the cross (x) in it that ties into the rear shock towers.

11-12-2003, 08:19 PM	#1
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	'00GT vs. Mach I Raced some kid in a new blue Mach I from about a 60mph roll on the freeway. I had a 260lb passenger and he was by himself. I dropped it into 3rd and stomped it and we were pretty much even all the way through 4th up to about 105 where I let off because I could see some cars up ahead. I thought I would get pulled on a little from a roll but it didn't happen. I wish the track was still open. I have surprised myself with the cars I hang with or beat since I got the 4.10s. I don't think I'm making more than 285 or so at the crank, but she runs about even with low-13 second cars on street tires if I get a good launch. __________________ Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s

11-12-2003, 09:42 PM	#2
fastang Registered Member Join Date: Aug 2000 Location: santa ana ca Posts: 1,349	SWEET! What kinda rpms are you turnin with those gears? Is first gear useless or hard to launch well with? __________________ 98 GT manual trans, Magna Flow exh. old car: 95GT, TFS T.W. heads, Holley Intake, B303 cam, FRPP 30lb injectors, Scorpion 1.6 rollers, 65mm TB, 73mm MAF, BBK Longtubes, Flowmaster cat back, March Pulleys, MSD coil, 9mm wires, Tremec 3550 trans, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors. 190lph pump, BBK adj FPR.

11-13-2003, 03:28 PM	#3
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	I'm turning about 2500 rpm at 70mph with a 5-speed and 285/40-17's out back. First gear is definitely trickier now, but if I just slip the clutch off the line and let it out just right as it gets rolling and I floor it I don't usually break traction as long as the road is smooth. If the road is not good it will spin them no matter what at the top of 1st. I have to shift a hair slower into 2nd on street tires or it will roast them good, but once I got used to it I am stomping other cars out of the hole. I also have stiffer springs than most folks run on the street, so if I can launch with 4.10s then anyone should be able to with practice. In front I have 350 lb/in coilovers, which is the equivalent of 1250 lb/in in the stock position. Out back I have 450 lb/in springs in the stock location with a torque arm and panhard bar. I'm sure if I ran softer springs it would be much easier to launch. __________________ Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s

11-13-2003, 06:24 PM	#4
Fox Body Mustang Maniac Join Date: Sep 2000 Location: GA, U.S.A Posts: 2,266	blue00gt, I gotta say, man, I've always loved how your car looks from the first time I saw it. Really like what you done to it, not much, but just enough (and also the color). Good race, BTW. Any other plans for the car in terms of engine or exhaust mods? __________________ 351W-powered 1979 Ford Mustang Ghia notchback '79 Video @ Idle Stock 5.8L under 4" cowl 'glass hood, C4 w/ Transgo shift kit, Holley 750 cfm, Edelbrock Performer RPM intake; Fluidyne Al radiator, Flexalite 175 electric fan, 1 5/8" MAC shorty headers, FRPP Al driveshaft; S&W 6-point cage; 2.5" Off road H-pipe, 2-chamber Flowmasters, 8.8" Rear w/ 3.55s; Weld wheels (15x6;15x8), Front: 225/60/15, Rear: 275/50/15 Nitto NT 555R Drag Radials; 14 x 4” K&N X-stream air filter. '92 GT (5-speed) Small In Car Video Stock 5.0L, 2-chamber Flowmasters, MAC CAI, Tri-Ax, Al pedals... "Red, thou art my companion. Hasten now your quickened metamorphosis to Green that I may conquer all who dare abide there beside me. May they be left thither behind burnt black." ---Fox Body

11-13-2003, 08:40 PM	#5
fastang Registered Member Join Date: Aug 2000 Location: santa ana ca Posts: 1,349	Thanks for clueing me in. I think Im gonna go with 373's though. I dont want to be turning 3 grand or more at 75-80 mph. __________________ 98 GT manual trans, Magna Flow exh. old car: 95GT, TFS T.W. heads, Holley Intake, B303 cam, FRPP 30lb injectors, Scorpion 1.6 rollers, 65mm TB, 73mm MAF, BBK Longtubes, Flowmaster cat back, March Pulleys, MSD coil, 9mm wires, Tremec 3550 trans, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors. 190lph pump, BBK adj FPR.

11-13-2003, 08:42 PM	#6
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	Thanks, Fox Body. As far as what's next for the stang, I have a Spec Stage II clutch, aluminum flywheel, and aluminum driveshaft that just need to be installed. After that I plan on saving up some money and getting the Kenne Belle twin screw 8psi intercooled kit early next year. The only thing left on my plan to buy after that is a roll cage, 5-point harnesses, rear seat delete, and Baer 12" rear brake kit. At that point I should have the full package as far as handling, braking, acceleration, and appearance. Nothing else to buy except what I break with the extra horsepower (maybe a T56 when the T45 dies). __________________ Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s

11-14-2003, 10:38 AM	#7
EZRIDN Registered Member Join Date: Jan 1999 Location: U.S.A. Posts: 504	Sweet run! __________________ '86 GT..5 spd....14.0 @ 98 SOLD '87 GT..5 spd...Stock...14.4 @ 97 SOLD '90 GT Conv. A4 Cream Puff...14.6 @ 94 SOLD '99 Z28..A4..Stock stall, no tuning, all motor, full weight 11.92 @ 117.95 SOLD '03 Centennal Edition GT 5 spd. 1 of 620 5 spd coupes made. http://bradbarnett.net/mustangs/timeline/99-04/03/100th.htm Stock..... 2.02 8.9 13.89 @ 99.03 http://bradbarnett.net/mustangs/timeline/99-04/03/100th.htm

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
04 Mach vs 03 Cobra	RBatson	Blue Oval Lounge	20	01-13-2004 09:07 PM
VIN question on 69 Mach 1	DRASTiK	Classic Mustangs	9	10-31-2002 06:06 PM
Mach I vs 02 GT	dod racing	Modular Madness	15	07-11-2002 06:20 PM
SportsRoof or Mach 1??? HELP!	6T9PONY	Classic Mustangs	14	10-30-2001 12:36 AM
1969 Mach 1 Options and Data tags HELP ! :-)	Barts_65	Classic Mustangs	3	10-26-2001 12:31 AM