![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2002
Location: NJ/gettysburg PA
Posts: 32
|
![]() this might be a stupid question but i am putting the pistons back into my motor and i put one in turn the crank,, out the opposite piston in etc... is there a pattern in which the pistons should be (example: #1 up, #2down,#3 up) i thought there was but my friend said as long as they are torqued to the crank right its ok... and how much should i torgue the end cap bolts to
Thanks Cait
__________________
Pretty in Pink Racing Black 85` GT hot pink 306 block , Rebuilt T-5, 650 Holley Carb, Edelbrock Victor Jr Intake, GT-40 Heads, MAC 1 3/4 headers, X- Pipe, Flowmaster 2 1/2 mufflers, MSD distributor, MSD 6al, MSD blaster 3 coil, , FMS aluminum driveshaft, 8 point cage, 4 inch cowl, 140 amp Power Master Alt. Moroso water pump, autolite gauges, monster tach, hurst short shifter, line lock, underdrive pullies, 3.73s and 8.8 auburn posi rear, 31 spline moser No this is not my boyfriends car and yes the motor is pink ![]() Making boys cry 1/4 mile at a time |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Jul 2000
Location: Norman, Oklahoma, USA
Posts: 597
|
![]() Honestly, I don't think it matters as far as a pattern goes. I would put both pistons onto one arm of the crank before you torque them down (like #1 and #5) Also, if your rods are stock, my machine shop told me not to torque them down to more than 25 pounds. The stock rods have little tiny cap bolts that will stretch easy. Anyway, good luck with your engine, I still want to see pics of the pink engine!!!
__________________
Michael Black QuantumMotorsports Norman, OK 1984 LX Hatch 306 w/ TRW forged flat toppers, Comp Cams Magnum 292H, GT40P heads w/ 3 angle valve job, .550 lift springs, Angus Racing Roller Rockers, Weiand Stealth Intake, Holley 4150 650cfm carb, MAC 1 5/8 Long Tubes, Single Chamber Flowmasters, 91' T5 w/ Pro 5.0 shifter, Turbo Coupe 8.8 Rear w/ 3.55 gears, QA1 Motorsports tubular K member, no interior except steering wheel and seat. Coming soon: 6 or 8 point cage, Fuel Cell, Weld Draglites |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
393 pistons | Ieatcamaros | Windsor Power | 0 | 03-24-2004 10:02 PM |
Largest cam in 351W without cutting the pistons (Looking at AFR185s) | Fox Body | Windsor Power | 10 | 06-15-2003 12:39 AM |
Cutting valve reliefs into early pistons | QuantumMotorsports | Windsor Power | 11 | 05-14-2003 09:22 PM |
Pistons for Larger Valves? | MustangChile | Classic Mustangs | 4 | 02-28-2003 01:27 AM |
What type of pistons should i get? :) | chickendreamer | Windsor Power | 14 | 09-12-2002 09:52 PM |