![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() Well I got there really late, and got in 6 runs in 2 hours. There was hardly anyone there it was great.
The car ran 12.5's all day with the roll cage, so any extra weight I guess was off set by losing the sound deadening etc. The 60's were in the low 1.7's with a 1.69 best for the day. Mph was all in the 107's. I tried the nitrous and something screwed up. I dont know what happend, it almost died at half track and I didnt feel any boost at all. So I didn't try it anymore. After leaving I noticed I had NO OIL PRESSURE! SO I pulled it over there, and had to spend the night in carlsbad. Anyways, I found I have a broken oil pump driveshaft. So that has to be fixed now, and I gotta find whats wrong with my Nitrous. Also ran my cousins 68 coupe. Which has a 315hp Crate motor with a T5Z tranny and 3.08's which ran a best of 14.6@94mph. Which is really screwed up. I made a post on it in Windsor power. Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.55@107 Motor |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: May 2000
Location: Everett, MA
Posts: 417
|
![]() Get the oil pump and nitrous fixed so we can find out how fast you're running!
|
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jun 2000
Location: ventura,CA
Posts: 438
|
![]() Dude that sucks. When I pulled apart my old stang's 302, the oil pump shaft looked like a twizzler. Fortunately, it didn't break. After that, I installed a heavy duty shaft and an autometer oil pressure warning light.
------------------ 92 GT, 4:10 gears, centerforce clutch, 6# powerdyne blower, bbk h-pipe, flowmasters |
![]() |
![]() |
![]() |
#4 |
IRAQ VET
Join Date: Feb 2000
Location: high desert California
Posts: 1,480
|
![]() sorry to hear the nitrous didn't work. Hope u get ur problems fixed.
------------------ 69 428 cobra jet: tons of mods. 97 f-150 5.4 xlt mark III BUCKLE UP. SUCK IT IN. Objects in the mirror are about to disappear... QUICKLY!!!!!! |
![]() |
![]() |
![]() |
#5 |
RICE taste like Chicken
Join Date: Jun 2000
Location: Edmond, OK
Posts: 687
|
![]() Sorry I didn't answer your messages Sky...I was out washing my car.
That really bites Yo. ------------------ Dustin Saleenized 89 GT,428 rwhp,TFS Street Heat Intake,TFS TW Heads,TFS #2 cam,BD-11A 9 psi,FRPP 1.6 rr's,BBK 70mm TB,Pro-M 75mm Bullet,MSD 6BTM, FMS 9mm wires,BBK longtubes,BBK Short H-pipe,American Thunder cat back,3.55's 12.3@119 http://www.mustangworks.com/rides/pictures/Listing1549-slot1.jpg |
![]() |
![]() |
![]() |
#6 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Damn, sorry to hear that Sky, I was looking to see your 11 sec times with the juice...make sure you get all the metal out of the motor from that broken shaft, double check the pump, you may just want to swap it since it is so cheap, get a ARP chrome-moly shaft and give it hell!
------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Feb 2000
Posts: 469
|
![]() damn that sux sky! Do you know what caused the shaft to break? If your oil pump siezed then somethin (like a lifter retainer ring) may have jammed her up. Friend of mine said to check your distributer too, says that if the gear/s are torn up, the you may have wiped out your cam too. (happened to him) Did you install the N2O system yourself? I think you mentioned that you did...at least you will know your way around it to troubleshoot it! |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Aug 2000
Location: santa ana ca
Posts: 1,349
|
![]() Damn dude, sorry to hear that you had to stay down there. How did you get home? Did you fix the car down there? You probably had to.
Get your nitrous fixed and I'll join you next time hopefully with a new motor that can keep up with your *** . ![]() BTW, Are you coming down to dyno your car with us on Saturday? You mentioned it before. ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors [This message has been edited by fastang (edited 07-09-2001).] |
![]() |
![]() |
![]() |
#9 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() I'll bring it down to dyno it if I can get it all fixed by then, but chances are it wont get fixed that fast, as I will need a whole day free to get into it.
I pulled the distributor and the gears on it are all fine. I'll just throw in a high volume oil pump with hardened shaft. Im pretty sure thats what blew it up. I think I may have had an empty n20 bottle. I had forgotten it turned on all day and night the day before, and maybe it seeped out? So I was thinking that I just got fuel and it went rich on me? Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 1.69 60' |
![]() |
![]() |
![]() |
#10 | |
Registered Member
Join Date: Feb 2000
Posts: 469
|
![]() Quote:
Also, your oil pump got shot but how? shafts break because of siezed pumps...usually caused by foriegn objects I believe. I'm not trying to sound like a doomsayer...just dont want you to throw a new pump on and wind up hurting the engine to the point where it gets really expensive |
|
![]() |
![]() |
![]() |
#11 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() It probably had 150k miles on it... but I don't know what caused it. What should I check for?
I didnt use any teflon tape, I didnt know I was supposed to. Sky ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 1.69 60' |
![]() |
![]() |
![]() |
#12 |
Registered Member
Join Date: Feb 2000
Posts: 469
|
![]() you are supposed to use teflon paste (not tape, it can ruin your solinoids, and clog your lines) you use it on ALL the pipe fittings, not the AN fittings. I am damn sure that you leaked out your nitrous because of it.
As far as your engine is concerned, get it flushed professionally flushed. I have never done that sort of thing before but i think they hook it up to a pump and just let oil get ran through it without the engine running (Dont quote me though, I may be wrong) when you pull your old pump, look to see if it got siezed by metal or something. I would call a mechanic though and see what they say. There is a chance that the motor might have to be taken out to make sure something more serious hasn't happened. I know this is all bad news but I may be wrong on the whole deal and maybe the pumps seals went bad and thats what caused it (hopefully) to fail. -ed |
![]() |
![]() |
![]() |
#13 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() Yeah, Im not busyn used stuff anymore
SKy ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 1.69 60' |
![]() |
![]() |
![]() |
#14 |
Registered Member
Join Date: Jun 2000
Location: ventura,CA
Posts: 438
|
![]() Yo Sky, stick with a standard oil pump. High volumes do not fair well in small Ford's. Causes extreme windage and pops the oil gallery plugs out. Belive me, it happened to me before. A standard oil pump will do just fine, unless it's an all out race motor.
![]() ------------------ 92 GT, 4:10 gears, centerforce clutch, 6# powerdyne blower, bbk h-pipe, flowmasters |
![]() |
![]() |
![]() |
#15 |
Registered Member
Join Date: May 1999
Location: moorpark ca
Posts: 340
|
![]() If the pump had 150K miles on it, that is probably why it died! It's a miracle it lasted that long! I would probably stick with a stock one as well. jmo. I'm sure you can just replace the pump and shaft! when you pull the oil pan just check for contaminates laying on the bottom of the pan! good luck sky!
how was the weather at Carlsbad? ------------------ 96 stang,ported 99 heads, 99 intake, 99 cams,Steeda power pullies,Kirban adj.reg.,Pro-m 87,24#inj.,70mm t/b,BBK longtube headers,Bassani x-pipe w/cats, Dynomax ultraflow catback,iat mod, home depot ram air, k@n, 373's,cobra brakes,fms spings, lakewood 90/10's and 50/50's tri-ax shifter. best et 13.80 best mph 103.3 bfg street tires,bakersfield, ca |
![]() |
![]() |
![]() |
#16 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() Yeah, it was a cool 70-75 degrees. It was great weather, and almost empty!
Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 1.69 60' |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Carlsbad results | ed1371 | Stang Stories | 3 | 09-23-2001 02:35 PM |
Famoso results - disapointing - next run Carlsbad 8/11? | withamc | Stang Stories | 6 | 07-30-2001 01:47 PM |
Carlsbad results? | Skyman | Stang Stories | 0 | 07-01-2001 01:31 AM |
Saturdays Famoso Results | fastang | Stang Stories | 7 | 06-26-2001 11:58 AM |
Carlsbad Results ??????? | gp001 | Stang Stories | 41 | 04-01-2001 12:33 PM |