MustangWorks.com : Ford Forums - View Single Post

dinomite · 07-17-2001, 02:09 PM

I posted this a couple weeks ago. ya don't wan to shift a stock 5liter above 5200 rpms, theres no power up there, and with the AOD you have to initiate the shift, cause its a slow tranny. to find the point where you can launch, PRACTICE. just leave from stop signs, don't race anyone but yourself. read on.

you like dancin? you better, cause its time for...The AOD Shuffle!

ok, start by putting your car into 1 (alllll the way down, press the button and put it back). put your left foot on the brake, and use your right foot to bring the revs to ~1500. when you are ready to go (don't sit like that too long, it will burn up your converter) release the brake and slowly depress the throttle. when the revs hit 4800, push the "gear selector lever" (i hate my auto too ) up one notch (to the "D" position). the tranny takes about 300 rpm to shift, and once it has fully shifted, and youve waited a second, press the button and pull it BACK to the "1" position. when the revs hit 4800 again, put it in "D" and leave it there. finally, when they hit 4800 put it into "OD", but by that time you will really be movin....i do the entire 1/4 in 2 gears, going just out of the powerband on my 90LX convert.

a stock mustang stops making power at about 5100ish,so given it takes 300 rpm for the anchor to shift, you move the shifter at 4800. your AOD has 4 gears, the "1" position only lets the tranny use first gear, the "D" position lets it use the first 3 (1,2,3 DUH!) and the "OD" position lets it use all 4. the problem is that if you let the transmission shift itself, it does so a few hundred rpm too early, this is worth a couple tenths in the 1/4. the other problem is that you only have a distinct position for 1st gear (the "1" position), and the first 3 (the "D" position). in order to keep it in 2nd gear till the perscribed rpm, you have to bring the shifter back to the "1" position, after letting it shift (by moving it from "1" to "D" and then back to "1"). Cause you have to do so much fancy work, its the aod shuffle. now, be careful when you are shifting into 2nd gear that you put it in the "D" position and leave it there long enough that it is completely done, before you bring it back to "1" otherwise it will downshift to 1st and that would be bad. if you ever feel quesy about doing this, just push the shifter forward as far as you can (WITHOUT pushing the button) and it will stop at "OD".

07-17-2001, 02:09 PM	#5
dinomite The Dude Join Date: Feb 2001 Location: Arlington, VA Posts: 1,262	I posted this a couple weeks ago. ya don't wan to shift a stock 5liter above 5200 rpms, theres no power up there, and with the AOD you have to initiate the shift, cause its a slow tranny. to find the point where you can launch, PRACTICE. just leave from stop signs, don't race anyone but yourself. read on. you like dancin? you better, cause its time for...The AOD Shuffle! ok, start by putting your car into 1 (alllll the way down, press the button and put it back). put your left foot on the brake, and use your right foot to bring the revs to ~1500. when you are ready to go (don't sit like that too long, it will burn up your converter) release the brake and slowly depress the throttle. when the revs hit 4800, push the "gear selector lever" (i hate my auto too ) up one notch (to the "D" position). the tranny takes about 300 rpm to shift, and once it has fully shifted, and youve waited a second, press the button and pull it BACK to the "1" position. when the revs hit 4800 again, put it in "D" and leave it there. finally, when they hit 4800 put it into "OD", but by that time you will really be movin....i do the entire 1/4 in 2 gears, going just out of the powerband on my 90LX convert. a stock mustang stops making power at about 5100ish,so given it takes 300 rpm for the anchor to shift, you move the shifter at 4800. your AOD has 4 gears, the "1" position only lets the tranny use first gear, the "D" position lets it use the first 3 (1,2,3 DUH!) and the "OD" position lets it use all 4. the problem is that if you let the transmission shift itself, it does so a few hundred rpm too early, this is worth a couple tenths in the 1/4. the other problem is that you only have a distinct position for 1st gear (the "1" position), and the first 3 (the "D" position). in order to keep it in 2nd gear till the perscribed rpm, you have to bring the shifter back to the "1" position, after letting it shift (by moving it from "1" to "D" and then back to "1"). Cause you have to do so much fancy work, its the aod shuffle. now, be careful when you are shifting into 2nd gear that you put it in the "D" position and leave it there long enough that it is completely done, before you bring it back to "1" otherwise it will downshift to 1st and that would be bad. if you ever feel quesy about doing this, just push the shifter forward as far as you can (WITHOUT pushing the button) and it will stop at "OD".