© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
10-06-2001, 04:00 PM | #1 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
14.691@94.70 FINALLY!!!
R/T ... .866
60 .... 2.240 330 ... 6.190 1/8 ... 9.477 MPH ... 74.61 1000 .. 12.309 1/4 ... 14.691 MPH ... 97.70 Thats With A 2000rpm Slip, And No Powershifting. Now I Need To Finish Off My Exhaust And Go Low 14s.... ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dynomax 2.5" Super Turbo Cat-Back, K&N Air Filter (Stock Air Box), Removed Air Silencer 14.691 @ 94.7 With A 2.24 60ft. 1988 Mustang GT |
10-06-2001, 04:28 PM | #2 |
Registered Member
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
|
Me and you would be a good race. I got my best time last weekend.
reaction--.522 60 ft-----2.0754 330 ft----6.1396 1/8th mi--9.4873 @74.01 1000 ft---12.3592 1/4 mi----14.7959 @93 Nice time With 3.73's and some cheater slicks you will be a low 14 sec. car If I were you I would get some nitto's as my next mod you can fit a 245 wide and that should get you 2 flat 60's and about a 14.3 Good luck! ------------------ 88 mustang gt convertible bored to 306 BBk equal length headers, mac cold air fender kit, 3.73 FMS gears, Steeds Tri-ax shifter, Steeda underdrive pullies, Custom off road X-pipe, 2 chamber flow masters, cowl hood, nitto drag radials, ford racing clutch, 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires. Edelbrock 1 1/2 inch drop springs. (Best E.T. 14.79@93mph @3000ft) |
10-06-2001, 04:51 PM | #3 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Nice time. Did you run 97 or 94 mph?
Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 332RWHP, 350rwtq |
10-06-2001, 06:01 PM | #4 |
Registered Member
Join Date: May 1999
Posts: 5,246
|
Well you got your 14's. Now it's off to the 13's zone. LOL!!
|
10-06-2001, 06:11 PM | #5 |
Registered Member
Join Date: Nov 1998
Location: Houston, Tx.
Posts: 3,887
|
What headers are planned? Correct ones should help.
Rev ------------------ '66 Coupe, 306, 300 HP, C-4, 13.97 e.t., 100.3 mph 1/4 mi. [This message has been edited by Rev (edited 10-06-2001).] |
10-07-2001, 08:07 PM | #6 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
sorry, thats a 94.70mph
i have bbk 1-5/8" equal legnth shortys, and can get a off road h pipe. that should help to a 14.2 or so (i hope) |
10-07-2001, 10:40 PM | #7 |
Registered Member
Join Date: Jun 2000
Location: sanantonio, Tx, usa
Posts: 1,407
|
Electric fan, i went from 94mph, to 98.
------------------ 90 lx coupe: 5spd, energy susp trans mounts, fms hd clutch, Mac coldair fenderwell, Mac h-pipe, supercoil, ADS chip, 160 stat, aluminum D/S, Black magic fan, 3.27grs. Best time: 13.9116(on 225/60/15 firehawks) Best mph: 98.17 Best 60': 1.9607 someday mods:4.10's, slicks. |
10-10-2001, 11:43 PM | #8 |
Registered Member
Join Date: Nov 2000
Location: Milwaukee,Wisconsin
Posts: 380
|
Congrats on your new time!
I just finished installing BBK 1 5/8" equal length shorty's tonight. If you need advice just e-mail me or post it. ------------------ '91 LX convertible , T-5,Centerforce Dual Friction, FMS adjustable cable w/quadrant, ported/polished/milled E7 heads, 1.6rr, 1.94/1.60 stainless valves, BBK 1 5/8" equal length shorties, 2 1/2" off road H-pipe, Summit 2 1/2" catback, March Performance Pulleys and A/C Eliminator |
10-12-2001, 09:22 AM | #9 |
Registered Member
Join Date: Dec 2000
Location: Waterloo, ON, Canada
Posts: 214
|
hey, nice times, I'm still a bit behind ya!!
------------------ 94 GT (triple black) FMS 95 17" Cobra R's / AL Driveshaft / 3.27's K&N, 12* timing, 180* thermostat, 190 lph MAC Shifter/Gauges/Pedals, Euro Clear Projectors & Corners My CAR! |
10-13-2001, 07:22 PM | #10 |
Being stroked is great
Join Date: Oct 1998
Location: Alberta, Canada
Posts: 772
|
Nice 60's Bowtie, especially with stock gears. I wish I was at sea level with you
------------------ '91 LX Hatch, 17x8.5 ROH ZR6's, lowered, 3.73's, offroad H pipe, SN Cobra cat-back, ASP pullies, 14° timing, C&L 76mm MAF, 170A 3G, B&M Ripper on a T5 Best ET run: 14.593 @ 94.62, 2.292 60' Best MPH run: 14.728 @ 95.72 mph, 2.423 60' Best 60': 2.230 1991 LX Hatch 5.0L |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Finally got a 5.0! | '94Vert5.0 | Windsor Power | 3 | 04-12-2003 08:29 AM |
I finally shut him up | bigred90gt | Stang Stories | 9 | 01-27-2003 04:53 PM |
Nitrous times, finally. | chris91LX | Windsor Power | 4 | 11-11-2002 07:58 PM |
AIt's finally here...(kina Long) | Stang951 | Windsor Power | 0 | 06-19-2001 12:00 PM |
THE BIG SHOT FINALLY WORKS!!! | NOSstang89 | Windsor Power | 2 | 05-16-2001 12:04 PM |