1st time at track.....my times

90lxracer · 11-29-2002, 11:58 PM

I went to the track tonite for my first time for a best of:
14.42-1/4
.802 - reaction
2.27 - 60 ft.
96.59 mph

Not bad i guess for my first time but i still need to work on my 60ft. times. By the way i was using ET streets.

Adam

Green93notch · 11-30-2002, 12:03 AM

deff get some gears, unless you want power, then ide go heads cam intake.. heres my ex..: i was turning 13.3s with 2.2- 2.3 60ft and 308 gears... when i just added my 373s on my very 1st run with them, i cut a 2.000 and ran a 12.85. gears are going to get you out the hole faster imo. specially with a DR. i use nittos. hope this helps.

Vinny

90lxracer · 11-30-2002, 01:20 AM

Yea...gears is next on my list. My car is a project car...my 1st one....i am getting heads/cam/intake later on. I never knew how much fun the track is...

88workcar · 11-30-2002, 06:23 AM

Congrats Dude

Mikerulz · 11-30-2002, 08:41 PM

Those are some awesome times. You do really need to get gears though. The difference will freak you right out. I was running 14.8's and with 3.73's I ran a 14.0 and thats the only thing I changed. The launch will be a bit different but 2 or 3 runs and you'll be hooking up no problem.

toevil1 · 12-05-2002, 12:22 AM

That's pretty good for your first time out. I agree your 60 ft time is a little slow for ET streets.

My very first time out I had a best 60 ft. time of 2.33 with falken 245/50/16 street radials. I was not happy with the 2.73 gears so two days later I bought 3.55s. Next time at the track I pulled a best of 2.08 but I was still loosing alot of lowend because I could only launch at 1500rpms or lower. I than bought a pair of used BFG 255/50/16 drag radials that looked like slicks and busted of a best of 1.90 60ft. It took me a few races to adapt to the drag radials though, I now launch at 4000rpms with a little tire spin. I also have a caspers electronics throttle enhancer and loosen my swaybar everytime I run.

89 GT 5spd.
1.90-60ft.
5.743-330ft.
1/8-9.001 @ 76.13mph

90lxracer · 12-05-2002, 05:37 PM

my car would bog down when i got a pretty good launch, i guess because i dont have enough hp or something. I was gettin some base times before i start puttin money into the car.

11-29-2002, 11:58 PM	#1
90lxracer Registered Member Join Date: Oct 2002 Location: houston, Texas Posts: 65	1st time at track.....my times I went to the track tonite for my first time for a best of: 14.42-1/4 .802 - reaction 2.27 - 60 ft. 96.59 mph Not bad i guess for my first time but i still need to work on my 60ft. times. By the way i was using ET streets. Adam __________________ 1990 lx 5.0L 5 spd. BBk Lt's/BBK o/r x-pipe/2 chamber flows/holley systemax upper intake/holley systemax lower intake/holley systemax heads/Lunati cam/timing chain/fms 1.6 rr's/ pro-m 80mm mass air/ 24# injectors/ 190lbh./fuel pressure regulator/BBK 70mm tb/BBK 70mm egr spcr/fms 3.73 gear/Fluidyne Aluminum Radiator/Ford Racing Water pump/Underdrive pulleys 1997 Chevy Silverado Z71 4x4 6'' Pro-comp triple shock lift / 35x12.5 Pro-comp x-terrains on 15x10 welds / 4.56 gear / hypertech power programmer / Flowmaster 40 series exhaust / 2 12'' Audiobahn subs powered by houston acoustic 900 watt amp / white face gauges

11-30-2002, 12:03 AM	#2
Green93notch Registered Member Join Date: Oct 2002 Location: Poughkeepsie, NY Posts: 41	deff get some gears, unless you want power, then ide go heads cam intake.. heres my ex..: i was turning 13.3s with 2.2- 2.3 60ft and 308 gears... when i just added my 373s on my very 1st run with them, i cut a 2.000 and ran a 12.85. gears are going to get you out the hole faster imo. specially with a DR. i use nittos. hope this helps. Vinny __________________ 1993 5.0 mustang coupe cobra upper and lower intake, TFS TW Alum. heads, TF 1.6 Roller rockers, TF stage one cam, mac 70 mm T/B, 76 C&L Air meter, FMS 24lb in. steeda pullies, Tremec 3550, FMS 373 gears, FPR, white face gauges, pro 5.0 shifter, 3 chamber flowmasters, Offroad h-pipe, Mac headers, Centerfource cluch, steeda clutch quadrant and cable, saleen wing, walbro 155 fuel pump, Eibach lowering springs 1 7/8", M.U. Sub-frames. Track Times: Lebonon Valley: before heads/cam 13.76 @ 101.74 60ft - 2.24 after but before gears - 13.26 @106.66 with 2.166 60' EnglishTown before gears - 2.34 60ft - 13.35 @108.12 Etown after - 12.851 @108.19 2.000 60ft

11-30-2002, 01:20 AM	#3
90lxracer Registered Member Join Date: Oct 2002 Location: houston, Texas Posts: 65	Yea...gears is next on my list. My car is a project car...my 1st one....i am getting heads/cam/intake later on. I never knew how much fun the track is... __________________ 1990 lx 5.0L 5 spd. BBk Lt's/BBK o/r x-pipe/2 chamber flows/holley systemax upper intake/holley systemax lower intake/holley systemax heads/Lunati cam/timing chain/fms 1.6 rr's/ pro-m 80mm mass air/ 24# injectors/ 190lbh./fuel pressure regulator/BBK 70mm tb/BBK 70mm egr spcr/fms 3.73 gear/Fluidyne Aluminum Radiator/Ford Racing Water pump/Underdrive pulleys 1997 Chevy Silverado Z71 4x4 6'' Pro-comp triple shock lift / 35x12.5 Pro-comp x-terrains on 15x10 welds / 4.56 gear / hypertech power programmer / Flowmaster 40 series exhaust / 2 12'' Audiobahn subs powered by houston acoustic 900 watt amp / white face gauges

11-30-2002, 06:23 AM	#4
88workcar Registered Member Join Date: Oct 1999 Location: Pierre Part, La. U.S.A. Posts: 1,850	Congrats Dude __________________ 88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle.

11-30-2002, 08:41 PM	#5
Mikerulz Registered Member Join Date: Apr 2002 Location: Canada Posts: 27	Those are some awesome times. You do really need to get gears though. The difference will freak you right out. I was running 14.8's and with 3.73's I ran a 14.0 and thats the only thing I changed. The launch will be a bit different but 2 or 3 runs and you'll be hooking up no problem. __________________ 90 LX H-pipe, Long tubes, 351 D00E Heads ported and polished, 3.73 gears, Holley air filter, Holley 155lph pump, sub frame connectors, 2 chamber flowmaster cat backs, cold air induction, under drive pulleys, Hurst Ripper shifter, Compucar EFI system (50 to 150hp), all on top of a pair of 26*8.5 Mickey thompsons. 12.81 at 110mph

12-05-2002, 12:22 AM	#6
toevil1 Registered Member Join Date: Sep 2002 Location: Los Angeles Posts: 39	That's pretty good for your first time out. I agree your 60 ft time is a little slow for ET streets. My very first time out I had a best 60 ft. time of 2.33 with falken 245/50/16 street radials. I was not happy with the 2.73 gears so two days later I bought 3.55s. Next time at the track I pulled a best of 2.08 but I was still loosing alot of lowend because I could only launch at 1500rpms or lower. I than bought a pair of used BFG 255/50/16 drag radials that looked like slicks and busted of a best of 1.90 60ft. It took me a few races to adapt to the drag radials though, I now launch at 4000rpms with a little tire spin. I also have a caspers electronics throttle enhancer and loosen my swaybar everytime I run. 89 GT 5spd. 1.90-60ft. 5.743-330ft. 1/8-9.001 @ 76.13mph

12-05-2002, 05:37 PM	#7
90lxracer Registered Member Join Date: Oct 2002 Location: houston, Texas Posts: 65	my car would bog down when i got a pretty good launch, i guess because i dont have enough hp or something. I was gettin some base times before i start puttin money into the car. __________________ 1990 lx 5.0L 5 spd. BBk Lt's/BBK o/r x-pipe/2 chamber flows/holley systemax upper intake/holley systemax lower intake/holley systemax heads/Lunati cam/timing chain/fms 1.6 rr's/ pro-m 80mm mass air/ 24# injectors/ 190lbh./fuel pressure regulator/BBK 70mm tb/BBK 70mm egr spcr/fms 3.73 gear/Fluidyne Aluminum Radiator/Ford Racing Water pump/Underdrive pulleys 1997 Chevy Silverado Z71 4x4 6'' Pro-comp triple shock lift / 35x12.5 Pro-comp x-terrains on 15x10 welds / 4.56 gear / hypertech power programmer / Flowmaster 40 series exhaust / 2 12'' Audiobahn subs powered by houston acoustic 900 watt amp / white face gauges

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I FINALLY have track times!!	Stang_Crazy	Stang Stories	11	07-31-2002 06:44 PM
Track times..first time out with the N20..	Rick 91GT	Windsor Power	5	07-23-2002 05:32 AM
Bad time at track, solution?	Capri306	Windsor Power	5	07-01-2002 01:46 PM
Track night , Times are disappointing again!	Oldschoolpony	Windsor Power	19	05-19-2002 07:02 PM
Again, new track times.	exgmguy	Stang Stories	20	04-19-2002 06:12 AM