MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Website Community > Stang Stories
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 03-22-2007, 08:25 PM   #1
Lethal5Oh
Registered Member
 
Join Date: Jun 2002
Location: Portage
Posts: 239
Default To Hell With Upr!!!!!

I purchased UPRs catted x pipe. It didnt fit. I installed it and it pushed the catback back about 2 inches, enough to touch the axle. I called them and they told me its copied dimension whys off the stock h pipe. BS! then they told me i had to cut my flow pipes. WHY?! if its supposed to be the same length as the stock pipe then i shouldnt have to modify anything, right? When i called they would barely let me get a word in. No offer to send me a new one to see if there was infact a manufacturing problem, but they are refunding my money, thats the only thing they will do for me. As of now they have lost a customer, and i intended on buying more stuff plus I already have a decent amount of their products. Let me hear your thoughts on the subject. Later
__________________
'95 GT convert. K&N, C&L mass air meter, Performance distributors sreamin demon coil, dyna mod, live wires, king cobra clutch, flowmaster american thunder exhaust, UPR billet adjustable shift handle, Crane Cams Fireball HI-6 box,underdrive pullies, 255lph fuel pump, UPr short throw shifter, caster camber plates, 03 cobra lower A arms, bullit suspension, cobra front brakes
Lethal5Oh is offline   Reply With Quote
Old 03-22-2007, 08:52 PM   #2
Rev
Registered Member
 
Rev's Avatar
 
Join Date: Nov 1998
Location: Houston, Tx.
Posts: 3,887
Default Re: To Hell With Upr!!!!!

Not familiar with UPR, but be glad they are refunding your money without too much of a hassle. Some outfits would just delay action again and again, hoping you would just get tired and go away. Some would say that since you attempted installation that they are off the hook. There are many horror stories out there. That's why I always pay with a credit card. I can just send it back and cancel the transaction if I have to.

Rev
__________________
'66 Coupe, 306, 350-375 HP, C-4, 13.07 e.t., 104.8 mph, 1/4 mi.

O.B.C. #2


'66 coupe
Rev is offline   Reply With Quote
Old 03-22-2007, 09:18 PM   #3
Unit 5302
Registered Member
 
Join Date: May 1999
Posts: 5,246
Default Re: To Hell With Upr!!!!!

I have yet to see an aftermarket H/X pipe with converters that fits. I've had a CATCO and 2 BBKs through Summit Racing and none of them fit for crap. Of course, then again, I technically had only 1 BBK because Summit shipped the same defective one back to me :roll:

Considering the amount of money you spend on them, you'd think that a manufacturer would give a crap about the junk they ship out the door.
Unit 5302 is offline   Reply With Quote
Old 03-22-2007, 10:01 PM   #4
Dark_5.0
Registered Member
 
Dark_5.0's Avatar
 
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
Default Re: To Hell With Upr!!!!!

My Mac cat back had to be heated and bent and cut and shortened before it fit right.

I am good with a Torch/welder etc... so it took about 30 minutes of my time to iron it out.
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim.
00' Lightning-Stock
88'CRX-13 second ego killer
Dark_5.0 is offline   Reply With Quote
Old 03-24-2007, 06:12 PM   #5
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: To Hell With Upr!!!!!

FWIW, I know the owner of UPR, we get discounts through UPR and I love there suspension products, although, I have never ordered exhaust through them, I do know that most exhaust doesn't fit perfectly, now if they sent you the wrong part number or year pipe, then they should fix the problem, I'm suprised to hear they wouldn't let you get a word in on the phone. On the other side of things, are you sure the catback on your car is stock and hasn't been modified just a bit to fit the last pipe? I have the newer cobra cat back 2 1/2 on my 88 and they had to be welded on a little different to half of the catback, anyway, either way, at least your getting your money back after you tried installation, most don't do that much....good luck. if your looking for off road pipes, I have a Bassani X( best fitting pipes IMO ) and a MAC H, with a bung welded into it for a wideband ( I have the plug for it too if you don't run a wideband ) for sale. Both used but in great shape. i went with long tubes..
__________________
USMC302 is offline   Reply With Quote
Old 03-27-2007, 08:09 PM   #6
Lethal5Oh
Registered Member
 
Join Date: Jun 2002
Location: Portage
Posts: 239
Default Re: To Hell With Upr!!!!!

Well usmc302 heres the deal. I installed the catback myself on the factory pipe. I compare refernce points on the floor pan between the upr pipe and the factory. they were different. ANyways, i called them back for the shipping tag and talked to a different guy who listened to me. I measured the pipe and he was supposed to measure another one and get back to me. No word so far. He did offer to pay for me to have the flow pipes modified but im not to thrilled about doing that especially since I want to spend 500 plus on a slp or magnaflow exhaust. Im going to try calling back tommorow, hopefully this will get straightened out and everyone will win. I hate having to be the a$$hole, but when it comes to spending 300 on something that doesnt fit, theres a problem.

P.S. I have a few of their products and like them and would like to get more. They even sent me new hein joints for my bumpsteer kit because one became loose. Thought that was cool.
__________________
'95 GT convert. K&N, C&L mass air meter, Performance distributors sreamin demon coil, dyna mod, live wires, king cobra clutch, flowmaster american thunder exhaust, UPR billet adjustable shift handle, Crane Cams Fireball HI-6 box,underdrive pullies, 255lph fuel pump, UPr short throw shifter, caster camber plates, 03 cobra lower A arms, bullit suspension, cobra front brakes
Lethal5Oh is offline   Reply With Quote
Old 03-28-2007, 11:00 AM   #7
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: To Hell With Upr!!!!!

Can't agree with you more, I just dropped $650 on ceramic coated longtubes and mid x pipe. They better fit perfect.
__________________
USMC302 is offline   Reply With Quote
Old 04-02-2007, 12:46 PM   #8
Lethal5Oh
Registered Member
 
Join Date: Jun 2002
Location: Portage
Posts: 239
Default Re: To Hell With Upr!!!!!

Just an update. All is good now. UPR agreed to pay $50 to have an exhaust shop fix the x pipe.
__________________
'95 GT convert. K&N, C&L mass air meter, Performance distributors sreamin demon coil, dyna mod, live wires, king cobra clutch, flowmaster american thunder exhaust, UPR billet adjustable shift handle, Crane Cams Fireball HI-6 box,underdrive pullies, 255lph fuel pump, UPr short throw shifter, caster camber plates, 03 cobra lower A arms, bullit suspension, cobra front brakes
Lethal5Oh is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Are You Going To Hell? STROKER BILLY Blue Oval Lounge 15 03-20-2003 05:41 PM
what the hell is going on now? ragtop5point0 Windsor Power 1 10-27-2002 03:26 PM
What the hell did I just do? fiveohpatrol Blue Oval Lounge 6 05-15-2002 06:51 PM
Pop Ups from hell inferno Blue Oval Lounge 9 12-01-2001 03:40 PM
What the Hell? StoplightWarrior Stang Stories 3 11-26-2001 12:37 AM


All times are GMT -5. The time now is 05:53 AM.


SEARCH