ANY RACE SHOPS IN KNOXVILLE, TENN...??

Cindy · 07-25-2001, 01:55 PM

I need to find out for a friend if there is a race shop in the vicinity of Knoxville or Dandridge, Tennessee??????

Thanks,

Cindy Crawford
Modular Motor 11
NMRA 7000

mustangII460 · 07-25-2001, 10:09 PM

Im sure there are some in Knoxville I just refuse to change.

"Whites Performance & Machine" is where I get my block/heads worked.

They are located between Kingsport And Bristol. "East Stone Drive" (423) 288-3881.

They have started to sell rebuilt motors with 3 year 100,000 mile waranty on them also.

They just finnished a friends Bowtie, 800 plus HP...

I work for Jefferson City.

Skeen machine in Jefferson City does a good block prep/ balancing etc. They do not assemble motors though. But I can find somone to put it together if you need.

Skeens" .30 over bore,turned crank,/resize rods-push on pistons/balance entire rotating assembly will set you back @ $ 500.00. minus your parts. Then start on the heads.

I live in Kodak. I am not familiar with any good machine shops in K-Town. However there are a few good High Performance parts shops in K-Town.

K-Town @ 1 mile south off of 640 on Broadway Blvd. The owner of "Hot Rod Barn" lives in Dandridge. Hes a nice old man.

Mail me if you need anything else.

Cindy · 07-26-2001, 08:21 AM

Okay thanks, i made a copy of this to give to my friends. They are moving in that area and needed some advice. They just had a drag racing accident where he was wife was pinning between two race cars and almost lost her leg. They have been thru a lot.

Thanks for your help.

Cindy Crawford

07-25-2001, 01:55 PM	#1
Cindy Registered Member Join Date: Jul 1999 Location: South Florida Posts: 93	ANY RACE SHOPS IN KNOXVILLE, TENN...?? I need to find out for a friend if there is a race shop in the vicinity of Knoxville or Dandridge, Tennessee?????? Thanks, Cindy Crawford Modular Motor 11 NMRA 7000

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Oct.11 Mid-Mich Toys for Tots Benefit drag race	Doug Dornbos	Ford Show & Go	0	09-29-2003 02:24 PM
I wanna drag race..... they wanna road race	Rev	Stang Stories	19	10-09-2002 03:11 PM
MY FIRST RACE!!!	#1 Pony	Stang Stories	7	07-01-2002 07:55 AM
Biggest Race I've Ever Had. 440vs302	Skyman	Stang Stories	51	03-02-2002 05:40 PM
My race vs 1997 GT!	Special K	Stang Stories	13	07-14-2001 12:21 PM

07-25-2001, 10:09 PM	#2
mustangII460 Factoy Five Roadster Join Date: May 2000 Location: Sevier Co,Tennessee Posts: 1,681	Im sure there are some in Knoxville I just refuse to change. "Whites Performance & Machine" is where I get my block/heads worked. They are located between Kingsport And Bristol. "East Stone Drive" (423) 288-3881. They have started to sell rebuilt motors with 3 year 100,000 mile waranty on them also. They just finnished a friends Bowtie, 800 plus HP... I work for Jefferson City. Skeen machine in Jefferson City does a good block prep/ balancing etc. They do not assemble motors though. But I can find somone to put it together if you need. Skeens" .30 over bore,turned crank,/resize rods-push on pistons/balance entire rotating assembly will set you back @ $ 500.00. minus your parts. Then start on the heads. I live in Kodak. I am not familiar with any good machine shops in K-Town. However there are a few good High Performance parts shops in K-Town. K-Town @ 1 mile south off of 640 on Broadway Blvd. The owner of "Hot Rod Barn" lives in Dandridge. Hes a nice old man. Mail me if you need anything else.

07-26-2001, 08:21 AM	#3
Cindy Registered Member Join Date: Jul 1999 Location: South Florida Posts: 93	Okay thanks, i made a copy of this to give to my friends. They are moving in that area and needed some advice. They just had a drag racing accident where he was wife was pinning between two race cars and almost lost her leg. They have been thru a lot. Thanks for your help. Cindy Crawford