|
Check this out! - Titanium shifter cover plates.
I am in the process of making a few shifter cover plates out of Titanium similar to the one pictured here:
http://www.indianastangers.com/2Fast...es/shifter.jpg That one is made from regular stainless. The titanium ones are a LOT lighter and will be more of a mirror polish, but will have four screws around the center hole to hold the boot in. I also have some Eaton safety rocker switches (the kind with the flip up red cover) and was thinking of mounting one in a few of them which could be used for NO2 arming, line lock, or whatever. These things are going to look killer! What do you guys think they would be worth with all the mounting hardware without the switches? ------------------ Gunning for 12's! http://www.indianastangers.com/2Fast..._brd_logo2.gif Buy your parts here ICQ# 42269241 |
Those are sweet. If I were running an interior in the drag car I would most definantely be wanting one.
------------------ '93 lx notch 4 banger (drive it to work currently), Using the 306, 8.8 posi, 4.10's, summit rear cover, elec. fan, cowl hood, wieand stealth intake, holley 650 d.p.carb., built c-4, e-303, full autometer guages, msd box, mallory unilite dist, and coil, roll cage, summit seat, subs, 15x10's in the back with slicks, skinnies up front, all in use for 1988 Hatch Drag Car. Hope to start running next year. Hoping for 7.20's after all is done with small motor. |
I need one for my 93 LX AOD shifter. I have a Lentech and had to make a switch for the overdrive delete. I experimented with the stock cover and cut out a hole and messed up. I thought I could just get a new one from work (Ford dealer) but they are not available anymore! Please let me know if you could make one for me. That is exactly what I would want, an AOD bezel with a hole for an on/off switch
------------------ 1993 Conv. LX 5.0, Air in the tires, Fuel in the tank, Put the top down, Floor it till it breaks! |
2fast where did you get that shifter knob...and how much did it run you..
------------------ '91 GT,T-5,air silencer removed,HD clutch,K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,180 thermostat,Competition gauges,C&L 76mm MAF,Accufab 70mm TB,TFS street heat intake,5inch Tach Waiting install:Nothing Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's ICQ#35670781 http://www.mustangworld.com/mpics/mwl1.gif |
I made the knob too. Being a machinist sure has its advantages when it comes to customizing http://www.mustangworks.com/msgboard/biggrin.gif
LfiveohX If you send me the dimensions and a drawing of the cover for the AOD I could probably make one easy enough. The ones I make for the 5 speed will require some modifications to the console, but are very minor. I'm not sure if the AOD covers mount the same way. Anyone know? Here's the arming switch I was thinking of installing in the covers if people wanted them... http://www.zex.com/store/graphics/00.../BigSwitch.gif |
Orders are almost full. I have room for one more. If you definately want one email me with what you want. Cost will be $35 + shipping.
------------------ Gunning for 12's! http://www.indianastangers.com/2Fast..._brd_logo2.gif Buy your parts here ICQ# 42269241 [This message has been edited by 2FastLX (edited 09-28-2001).] |
COME ON ! Make one for the SN-95 !!!
: ) They look sweet !! ------------------ 94 GT (triple black) FMS 95 17" Cobra R's / AL Driveshaft / 3.27's K&N, 12* timing, 180* thermostat, 190 lph MAC Shifter/Gauges/Pedals, Euro Clear Projectors & Corners My CAR! |
The SN95 covers are curved and I don't have anything available to me to make anything like that. Sorry.
Orders are full. I'll make a new post when I am able to make more. |
| All times are GMT -5. The time now is 07:59 PM. |