The drag pack is back!

91evilstang · 05-26-2001, 03:52 PM

Have you guys seen the new drag pack mustangs?They are awsome!Their was an article in mm&ff their will be a stage 1 & 2 stage 1 you get a revised air box 260 ponys ,your choice of weld prostars or draglites(fats and skinnies factory!)nitto drag radials ,quick disconnect sway bar ,drag suspension including air bag on the rear passenger side and "better"upper and lower control arms,drive shaft safty loop ,31 spline axles ,welded axle tubes,braced rear end cover,a coustom chip,your choice of a tremic 5 speed a lentic auto or a viper t56 6 speed,you also get line lock already installed and you even get a helmit.thats all i can think of i might have missed some but any way the stage2 comes with a vortec Strim blower and a functioning shaker hood scoop and 375hp and 355foot pounds of torque.WWWWOOOOWWWW!!!All that stuff in it self isnt THAT wild but the fact that its from the factory makes it 10x cooler.Maybe high gas prices and all the muscle car is back in a big way.Thought i would share my excitement cant wait to see if the price tag is non astronmical.

------------------
91GT Flowmaster 2 chambers,off road H pipe,mac equalength headers,F303 cam,high lift valve springs ,svo 1.6 roller rockers,14*timing,410's,BBK cold air kit,hurst shifter, Pullys,World class T5 MSD 6al box. Ran 13.5@101 with stock headers and air box.

PGkelly · 05-26-2001, 04:21 PM

huh? i haven't heard of it, but ok. sounds cool. can you get more info? a link maybe?

------------------
If it ain't broke, make it go faster

AOL: MCVillain45

fastang · 05-26-2001, 04:24 PM

Sounds bad *** . Gimmie some more info.

------------------
95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

Unit 5302 · 05-26-2001, 04:33 PM

Looks like I'll be buying a MM&FF mag to check the article out.

I'll believe it when I see it.

Mercury · 05-26-2001, 04:50 PM

If its true, I'll be putting all three of my stangs in the paper FOR SALE, that is after I change my underwear.

If its true, looks like Ford is finally getting the picture.

lx mike · 05-26-2001, 06:27 PM

Not Very Likely Ford would Build Such a Vehicle.

------------------
93-LX: 5 Speed, Flow's with H-Pipe, 3.73's Sub's and K&N.

[This message has been edited by lx mike (edited 05-26-2001).]

[This message has been edited by lx mike (edited 05-26-2001).]

[This message has been edited by lx mike (edited 05-26-2001).]

red82gt · 05-26-2001, 06:35 PM

If they really do this then i'd better hurry up and finish school so I can buy one!

I thought Ford would've made a drag-pack focus or somthing dumb like that.

------------------
GT-40 heads (ported, polished, + milled), B303 cam, 1.7rr's, JE pistons, Offy intake, Carter AFB 625cfm carb, Flowtech 1 5/8" shortys, Flowtech X-pipe, MAC Flowpath exhaust, MAC pulleys, 373's, subframes, Eibachs+Tokicos, B+M ripper, FMS Clutch, Zoom Quadrant+cable, 17" CSA Ultra rims, 235/45ZR17 Yokohama AVS S4's, MSD 6A ignition+coil, FMS 9mm wires, Carbed, Naturally Aspirated, and Nasty!

89LXCarb · 05-27-2001, 11:19 AM

yes it is true I have read the article. But I don't think that ford builds them. It's some tuner company. Who cares about that, though, it's a drag pak!!

------------------
4 cyl converted to 302
comp cams cam, ported GT 40 heads, Edelbrock intake, holley carb
Turbo coupe rear with 373's
4 inch cowl hood
finally done after what seemed like forever!!!!!

FivepointOH · 05-27-2001, 12:50 PM

If I remember correctly it's a specific ford DEALERSHIP that makes these... I think they do have a warranty and stuff though but can't remember....

------------------
92 AOD GT, K&N, ram air, pulleys, 2 ch. flowmasters, 4:10's, shift kit, 1 5/8 mac longtubes and offroad hpipe 14.249 @ 97.34 mph before the headers and hpipe

red82gt · 05-27-2001, 01:11 PM

It probably is a dealership offering this. Ford wouldn't take a liability risk that big.

91evilstang · 05-27-2001, 01:42 PM

Oops sorry guys I just skimmed that article and got the "important" stuff out of it(how much horse and what goodies)and i am sorry to say i was mistaken that FORD isnt makeing these a company called Pauls high preformance and a spesific dealership is producing these but they are still mighty cool.sorry about any confusion.I would still like to see how much they are.

------------------
91GT Flowmaster 2 chambers,off road H pipe,mac equalength headers,F303 cam,high lift valve springs ,svo 1.6 roller rockers,14*timing,410's,BBK cold air kit,hurst shifter, Pullys,World class T5 MSD 6al box. Ran 13.5@101 with stock headers and air box.

lx mike · 05-27-2001, 03:20 PM

I found who makes them, it's http://www.paulshp.com/ and they are pricey stage one is 11,850 over stickerand stage 2 is 22,750 over sticker

Quote:

A "TURN-KEY" DRAGSTRIP / STREET MUSTANG GT - READY TO GO DOWN
THE STRIP IN THE 12'S @ 105+ MPH - OR - DOWN THE STREET IN THAT
CLASSY EYE-CATCHING, NEW EDGE MUSTANG DESIGN.

------------------
93-LX: 5 Speed, Flow's with H-Pipe, 3.73's Sub's and K&N.

Try Me · 05-27-2001, 09:32 PM

Sounds like EXACTLY how every Mustang GT should come from the factory.

My buddy is taking delivery of his '01 on Wednesday. Lizard King, he's the same guy who rolled his 'Notch duking it out with a WS6 a couple of weeks ago - he's looking forward to meeting you

LincoConti87 · 05-29-2001, 10:41 AM

I'm pretty sure the drag pak ford offered on the older mustangs was just something like a tachometer and a couple other pretty small things...how could you get confused with this?

Mercury · 05-29-2001, 12:00 PM

The drag pack ford offered on the older cars, like the 69-70 Mustangs was alot more than a Tach and small stuff.

The rear gear was usually kicked up to 4.10's or higher, there were also heavy duty Tranny and Oiler coolers, suspension pieces, traction bars, I believe also Sub Frames.

There werent any engine mods in ways of performance, but the chassis and durability of the cars and engines were tweaked heavily (well considering the time period).

Oh and they also added a tach.

dinomite · 05-30-2001, 07:14 AM

Drag pack???? PFPBT! I want a road-race pack.....oh wait, that would be the 55k cobra r!

lx mike · 05-30-2001, 05:08 PM

It on page 50 of the july issue of Muscle Mustangs Mag, says the stage 2 has run a 12.93 at 105.91mph.

Mustang92 · 05-31-2001, 05:48 AM

I'm not at all impressed by the stage 2 car. I was at the NMRA race in Reynolds and it was running there. I'm sorry but for what it has (blower, auto, DR's) it should go much quicker than it did. The MPH is very low as well. I lined up against him in qualifying and had seen the blower in the pits. I figured this guy would walk by me. It never happened.

To be honest both of these are over priced in my opinion. I've added the price up for parts and I could build the same car for much cheaper. If you have to pay for the work it might still come in cheaper than paying their premium. Of course I may be a little baised since my car runs quicker than both Stage 1 and 2 with less work and much much cheaper price tag.

------------------
00 GT, MAC Offroad H, Steeda Pulleys & Timing Adjuster, 4.10’s, Flows w/turndowns, UPR shifter, UPR Pro Series LCA’s, Lakewood 70/30’s & 50/50’s, Weld Pro Stars, Kaenen Cobra R Hood, 253.8 RWHP/292.8RWTQ
12.91@101.93 (1.74 60ft)
M/M 100, 7085
Recent Pic from Moroso

05-26-2001, 03:52 PM	#1
91evilstang Registered Member Join Date: Mar 2001 Location: lafayette IN USA Posts: 48	The drag pack is back! Have you guys seen the new drag pack mustangs?They are awsome!Their was an article in mm&ff their will be a stage 1 & 2 stage 1 you get a revised air box 260 ponys ,your choice of weld prostars or draglites(fats and skinnies factory!)nitto drag radials ,quick disconnect sway bar ,drag suspension including air bag on the rear passenger side and "better"upper and lower control arms,drive shaft safty loop ,31 spline axles ,welded axle tubes,braced rear end cover,a coustom chip,your choice of a tremic 5 speed a lentic auto or a viper t56 6 speed,you also get line lock already installed and you even get a helmit.thats all i can think of i might have missed some but any way the stage2 comes with a vortec Strim blower and a functioning shaker hood scoop and 375hp and 355foot pounds of torque.WWWWOOOOWWWW!!!All that stuff in it self isnt THAT wild but the fact that its from the factory makes it 10x cooler.Maybe high gas prices and all the muscle car is back in a big way.Thought i would share my excitement cant wait to see if the price tag is non astronmical. ------------------ 91GT Flowmaster 2 chambers,off road H pipe,mac equalength headers,F303 cam,high lift valve springs ,svo 1.6 roller rockers,14*timing,410's,BBK cold air kit,hurst shifter, Pullys,World class T5 MSD 6al box. Ran 13.5@101 with stock headers and air box.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Need Help, Budget Drag Suspension...	BowTie Eater 5 Liter	Windsor Power	6	07-24-2002 07:56 AM
Time to go back to school.	Unit 5302	Modular Madness	12	04-27-2002 03:46 PM
New 1/4 mile ET from the drag strip!!!!!!!!!!	Fox Body	Blue Oval Lounge	18	03-11-2002 05:22 AM
SD to mass air, back to SD?	fiveohpatrol	Windsor Power	16	02-09-2002 04:58 PM
Eibach drag springs + Tokico drag struts	Greystang302	Windsor Power	6	01-01-2002 01:46 AM

05-26-2001, 04:21 PM	#2
PGkelly Registered Member Join Date: Feb 2001 Posts: 274	huh? i haven't heard of it, but ok. sounds cool. can you get more info? a link maybe? ------------------ If it ain't broke, make it go faster AOL: MCVillain45

05-26-2001, 04:24 PM	#3
fastang Registered Member Join Date: Aug 2000 Location: santa ana ca Posts: 1,349	Sounds bad *** . Gimmie some more info. ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

05-26-2001, 04:33 PM	#4
Unit 5302 Registered Member Join Date: May 1999 Posts: 5,246	Looks like I'll be buying a MM&FF mag to check the article out. I'll believe it when I see it.

05-26-2001, 04:50 PM	#5
Mercury The Redneck James Bond Join Date: Sep 2000 Location: Fayetteville NC Posts: 1,707	If its true, I'll be putting all three of my stangs in the paper FOR SALE, that is after I change my underwear. If its true, looks like Ford is finally getting the picture.

05-26-2001, 06:27 PM	#6
lx mike Undescribable Join Date: Sep 1998 Location: Ft Myers Fla Posts: 1,539	Not Very Likely Ford would Build Such a Vehicle. ------------------ 93-LX: 5 Speed, Flow's with H-Pipe, 3.73's Sub's and K&N. [This message has been edited by lx mike (edited 05-26-2001).] [This message has been edited by lx mike (edited 05-26-2001).] [This message has been edited by lx mike (edited 05-26-2001).]

05-26-2001, 06:35 PM	#7
red82gt Sober voice of Reason Join Date: Nov 1998 Location: Kelowna, B.C., Canada Posts: 1,514	If they really do this then i'd better hurry up and finish school so I can buy one! I thought Ford would've made a drag-pack focus or somthing dumb like that. ------------------ GT-40 heads (ported, polished, + milled), B303 cam, 1.7rr's, JE pistons, Offy intake, Carter AFB 625cfm carb, Flowtech 1 5/8" shortys, Flowtech X-pipe, MAC Flowpath exhaust, MAC pulleys, 373's, subframes, Eibachs+Tokicos, B+M ripper, FMS Clutch, Zoom Quadrant+cable, 17" CSA Ultra rims, 235/45ZR17 Yokohama AVS S4's, MSD 6A ignition+coil, FMS 9mm wires, Carbed, Naturally Aspirated, and Nasty!

05-27-2001, 11:19 AM	#8
89LXCarb Registered Member Join Date: Jan 2000 Location: Columbus Grove, Ohio, USA Posts: 267	yes it is true I have read the article. But I don't think that ford builds them. It's some tuner company. Who cares about that, though, it's a drag pak!! ------------------ 4 cyl converted to 302 comp cams cam, ported GT 40 heads, Edelbrock intake, holley carb Turbo coupe rear with 373's 4 inch cowl hood finally done after what seemed like forever!!!!!

05-27-2001, 12:50 PM	#9
FivepointOH Registered Member Join Date: Jan 1999 Location: Sugar Land, Tx USA Posts: 478	If I remember correctly it's a specific ford DEALERSHIP that makes these... I think they do have a warranty and stuff though but can't remember.... ------------------ 92 AOD GT, K&N, ram air, pulleys, 2 ch. flowmasters, 4:10's, shift kit, 1 5/8 mac longtubes and offroad hpipe 14.249 @ 97.34 mph before the headers and hpipe

05-27-2001, 01:11 PM	#10
red82gt Sober voice of Reason Join Date: Nov 1998 Location: Kelowna, B.C., Canada Posts: 1,514	It probably is a dealership offering this. Ford wouldn't take a liability risk that big.

05-27-2001, 01:42 PM	#11
91evilstang Registered Member Join Date: Mar 2001 Location: lafayette IN USA Posts: 48	Oops sorry guys I just skimmed that article and got the "important" stuff out of it(how much horse and what goodies)and i am sorry to say i was mistaken that FORD isnt makeing these a company called Pauls high preformance and a spesific dealership is producing these but they are still mighty cool.sorry about any confusion.I would still like to see how much they are. ------------------ 91GT Flowmaster 2 chambers,off road H pipe,mac equalength headers,F303 cam,high lift valve springs ,svo 1.6 roller rockers,14*timing,410's,BBK cold air kit,hurst shifter, Pullys,World class T5 MSD 6al box. Ran 13.5@101 with stock headers and air box.

05-27-2001, 09:32 PM	#13
Try Me Registered Member Join Date: Jul 2000 Location: Ottawa, Ontario, Canada Posts: 465	Sounds like EXACTLY how every Mustang GT should come from the factory. My buddy is taking delivery of his '01 on Wednesday. Lizard King, he's the same guy who rolled his 'Notch duking it out with a WS6 a couple of weeks ago - he's looking forward to meeting you

05-29-2001, 10:41 AM	#14
LincoConti87 Registered Member Join Date: Dec 2000 Location: Tallahassee,Florida,USA Posts: 188	I'm pretty sure the drag pak ford offered on the older mustangs was just something like a tachometer and a couple other pretty small things...how could you get confused with this?

05-29-2001, 12:00 PM	#15
Mercury The Redneck James Bond Join Date: Sep 2000 Location: Fayetteville NC Posts: 1,707	The drag pack ford offered on the older cars, like the 69-70 Mustangs was alot more than a Tach and small stuff. The rear gear was usually kicked up to 4.10's or higher, there were also heavy duty Tranny and Oiler coolers, suspension pieces, traction bars, I believe also Sub Frames. There werent any engine mods in ways of performance, but the chassis and durability of the cars and engines were tweaked heavily (well considering the time period). Oh and they also added a tach.

05-30-2001, 07:14 AM	#16
dinomite The Dude Join Date: Feb 2001 Location: Arlington, VA Posts: 1,262	Drag pack???? PFPBT! I want a road-race pack.....oh wait, that would be the 55k cobra r!

05-30-2001, 05:08 PM	#17
lx mike Undescribable Join Date: Sep 1998 Location: Ft Myers Fla Posts: 1,539	It on page 50 of the july issue of Muscle Mustangs Mag, says the stage 2 has run a 12.93 at 105.91mph.

05-31-2001, 05:48 AM	#18
Mustang92 Drag Racer! Join Date: Nov 1999 Location: Lake Worth, FL USA Posts: 757	I'm not at all impressed by the stage 2 car. I was at the NMRA race in Reynolds and it was running there. I'm sorry but for what it has (blower, auto, DR's) it should go much quicker than it did. The MPH is very low as well. I lined up against him in qualifying and had seen the blower in the pits. I figured this guy would walk by me. It never happened. To be honest both of these are over priced in my opinion. I've added the price up for parts and I could build the same car for much cheaper. If you have to pay for the work it might still come in cheaper than paying their premium. Of course I may be a little baised since my car runs quicker than both Stage 1 and 2 with less work and much much cheaper price tag. ------------------ 00 GT, MAC Offroad H, Steeda Pulleys & Timing Adjuster, 4.10’s, Flows w/turndowns, UPR shifter, UPR Pro Series LCA’s, Lakewood 70/30’s & 50/50’s, Weld Pro Stars, Kaenen Cobra R Hood, 253.8 RWHP/292.8RWTQ 12.91@101.93 (1.74 60ft) M/M 100, 7085 Recent Pic from Moroso