MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 06-09-2001, 08:00 AM   #1
Dark_5.0
Registered Member
 
Dark_5.0's Avatar
 
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
Post Replacing convertible top. How hard is it?

I have an 88GT convertible I bought the car really cheap cause someone had vandalized it. Slashed the top tore up the rear window and keyed the paint. I have repaired everything except for the top. It is stitched up and dont look too good.

Have any of you ever replaced a convertible top and if so how hard was it to do.

I have to replace the top the headliner and I want to install a glass rear window.

How hard will it be and how much do you think it will cost? Thanks in advance

------------------
88 mustang gt convertible bored to 306 BBk equal length headers mac cold air fender kit cowl hood nitto drag radials ford racing clutch flow masters h-pipe 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires.
best 60 ft 2.14, best 1/8th 9.65, best 1/4 15.2 @89mph
Dark_5.0 is offline   Reply With Quote
Old 06-09-2001, 09:08 AM   #2
Maroon 5.0 LX
Registered Member
 
Maroon 5.0 LX's Avatar
 
Join Date: Mar 2001
Location: Southern Maryland
Posts: 471
Post

I replaced the top on an old '72 LTD some years ago. I suspect the basics are still the same. It'll probably take a week-end to do it.

Check with a local shop and see what they charge, then see if it's worth doing it yourself.

For a first timer, it's a little time consuming, but can be done. Just get a good top and rear glass. Biggest problem was making sure all the wrinkles were out. Most tops come with installation instructions, just follow them.

If you can walk and chew gum at the same time, you should be able to do it.

------------------
'89 LX 5.0 - 5 speed. Original Owner
'94 E-150 Conversion Van
Maroon 5.0 LX is offline   Reply With Quote
Old 06-09-2001, 09:54 AM   #3
jimberg
Registered Member
 
jimberg's Avatar
 
Join Date: Oct 1998
Location: Rogers, MN
Posts: 2,089
Post

I replaced my top. I'd probably pay to have it done next time. If you decide to do it yourself, make sure you have a 1/4 crown air stapler. The instructions on how to do it are in the official shop manual. If you don't have them, I can probably scan them for you.

------------------
351W 89 Mustang GT Convertible
jimberg is offline   Reply With Quote
Old 06-09-2001, 10:38 AM   #4
Dark_5.0
Registered Member
 
Dark_5.0's Avatar
 
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
Post

Thanks for the info guys. I want the top to look really good so I think I am leaning towards having it done but I think that having it done would quadruple the price.

Lets see pay to have new top installed or buy the mass air conversion kit. Hmmmm.

355.00 for the top and window VS. 800.00 for the installation.

The difference is a fat chunck of cash. My confidence is not too high for this project.

But the difference in cash is substantial.

------------------
88 mustang gt convertible bored to 306 BBk equal length headers mac cold air fender kit cowl hood nitto drag radials ford racing clutch flow masters h-pipe 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires.
best 60 ft 2.14, best 1/8th 9.65, best 1/4 15.2 @89mph
Dark_5.0 is offline   Reply With Quote
Old 06-09-2001, 11:04 AM   #5
jimberg
Registered Member
 
jimberg's Avatar
 
Join Date: Oct 1998
Location: Rogers, MN
Posts: 2,089
Post

Odds are good that if you do it yourself it may not be perfect but it won't look horrible, either. Besides, you live in TX. It will be down most of the time.

------------------
351W 89 Mustang GT Convertible
jimberg is offline   Reply With Quote
Old 06-09-2001, 03:08 PM   #6
Dark_5.0
Registered Member
 
Dark_5.0's Avatar
 
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
Post

Quote:
Originally posted by jimberg:
Odds are good that if you do it yourself it may not be perfect but it won't look horrible, either. Besides, you live in TX. It will be down most of the time.

This is true, I am just tired of people asking me what happened to my car at the track.



------------------
88 mustang gt convertible bored to 306 BBk equal length headers mac cold air fender kit cowl hood nitto drag radials ford racing clutch flow masters h-pipe 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires.
best 60 ft 2.14, best 1/8th 9.65, best 1/4 15.2 @89mph
Dark_5.0 is offline   Reply With Quote
Old 06-09-2001, 03:46 PM   #7
Maroon 5.0 LX
Registered Member
 
Maroon 5.0 LX's Avatar
 
Join Date: Mar 2001
Location: Southern Maryland
Posts: 471
Post

$445 sounds like a lot for labor. But I guess if they're fast and good, it'll be worth it.

------------------
'89 LX 5.0 - 5 speed. Original Owner
'94 E-150 Conversion Van
Maroon 5.0 LX is offline   Reply With Quote
Old 06-09-2001, 09:01 PM   #8
crewzin
Registered Member
 
crewzin's Avatar
 
Join Date: May 2001
Location: Sour Lake, TX
Posts: 211
Post

Pay to have it done! TRUST ME. If you get it wrong you will waste the new top. Its a pain in the azz. Lots of money for a top and install but if it gets loose or something you can take it back to the installer. Plus having the receipt will help with insurance if it gets ripped again.
crewzin is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
replacing outer door handle...how hard? 82 GT Windsor Power 3 03-03-2004 06:09 PM
T5 hard to shift after replacing bearing retainer Merlin76 Windsor Power 8 02-20-2004 10:22 PM
replacing side view mirror...how hard? 82 GT Windsor Power 2 02-11-2004 11:31 PM
replacing hard brake lines 82 GT Windsor Power 0 05-26-2002 02:57 PM
Replacing convertible top madmiamian Appearance & Detailing 0 04-11-2002 07:46 PM


All times are GMT -5. The time now is 06:56 AM.


SEARCH