HELP: Video clip of rear-end sway problem

Gautam · 06-25-2001, 02:41 PM

Hi,
Well, I finally made a small video of how
my rear end looks when you launch. Video
is kinda small, and there's no sound, but
pay close attention to the last 2 seconds
and you will see the twist near the end.

Here's the video (900KB, 6 sec., MPEG)

Also, the gold piece (with two black bolts)
that is on the front of driver side's upper
control arm, has a crack on it:

NOTE: This is not the underside of my car.

I know my rear end is supposed to twist on
launching, but I've never seen it twist/sway
that hard before.

Thanks!
Bye!

------------------
Gautam N. Lad
http://www.cubicdesign.com
http://www.cubicdesign.com/mustang/

[This message has been edited by Gautam (edited 06-25-2001).]

[This message has been edited by Gautam (edited 06-25-2001).]

06-25-2001, 05:45 PM

Mine doesn't do it that bad, but my car does do that. Are you talking about a crack on that exhaust hanger (what it looks like) or the crack looking thing on the upper control arm mount?
Have you seen a crack in the upper control arm mount on your car?

------------------
'84 Mustang 5.0 LX
My car

Gautam · 06-25-2001, 06:10 PM

Hi,
No, its not the muffler hanger. The gold
piece that's shaped like a brake pad in
the picture is what has a crack....

I updated that pic with a red crack so you
know where it's cracked.

And no, the control arms don't have cracks on them anywhere.

Also, you can see that once the car
launches, it sways side to side a bit
before it settles down. Hopefully
this is a case of needing new LCAs.

Bye!

------------------
Gautam N. Lad
http://www.cubicdesign.com
http://www.cubicdesign.com/mustang/

[This message has been edited by Gautam (edited 06-25-2001).]

06-25-2001, 02:41 PM	#1 (permalink)
Gautam Registered Member Join Date: Sep 2000 Location: Brampton, ON, Canada Posts: 298	HELP: Video clip of rear-end sway problem Hi, Well, I finally made a small video of how my rear end looks when you launch. Video is kinda small, and there's no sound, but pay close attention to the last 2 seconds and you will see the twist near the end. Here's the video (900KB, 6 sec., MPEG) Also, the gold piece (with two black bolts) that is on the front of driver side's upper control arm, has a crack on it: NOTE: This is not the underside of my car. I know my rear end is supposed to twist on launching, but I've never seen it twist/sway that hard before. Thanks! Bye! ------------------ Gautam N. Lad http://www.cubicdesign.com http://www.cubicdesign.com/mustang/ [This message has been edited by Gautam (edited 06-25-2001).] [This message has been edited by Gautam (edited 06-25-2001).]

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Please help stutering problem	Just me	Windsor Power	10	10-18-2002 03:37 PM
Brake Problem Update	Kisner	Classic Mustangs	1	03-12-2002 01:19 PM
rear end problem	1980convertible	Windsor Power	3	02-12-2002 08:39 PM
Who makes a good heavy duty rear sway bar?	8850	Windsor Power	5	10-18-2001 07:19 PM
problem with rear bumper facia	mustang marty gt	Appearance & Detailing	0	08-24-2001 03:13 AM

06-25-2001, 05:45 PM	#2 (permalink)
84stangLX Posts: n/a	Mine doesn't do it that bad, but my car does do that. Are you talking about a crack on that exhaust hanger (what it looks like) or the crack looking thing on the upper control arm mount? Have you seen a crack in the upper control arm mount on your car? ------------------ '84 Mustang 5.0 LX My car

06-25-2001, 06:10 PM	#3 (permalink)
Gautam Registered Member Join Date: Sep 2000 Location: Brampton, ON, Canada Posts: 298	Hi, No, its not the muffler hanger. The gold piece that's shaped like a brake pad in the picture is what has a crack.... I updated that pic with a red crack so you know where it's cracked. And no, the control arms don't have cracks on them anywhere. Also, you can see that once the car launches, it sways side to side a bit before it settles down. Hopefully this is a case of needing new LCAs. Bye! ------------------ Gautam N. Lad http://www.cubicdesign.com http://www.cubicdesign.com/mustang/ [This message has been edited by Gautam (edited 06-25-2001).]

Sponsored Links