© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-19-2002, 12:51 PM | #1 |
Registered Member
Join Date: Jul 2001
Location: Seattle, WA
Posts: 381
|
Is this a project I could handle?!? (Intake, heads, cam...)
Hello,
I installed my exhaust and my cold air intake (very simple)...I have no experience with installing any of the three mentioned in the subject. I am just curious how involved of a project this would be. How long I would have to expect to spend working on it. And is a reasonable project for me to take on?!? I really want the gains I would get from these, but don't want to pay for installation Also, are there any overview installation instructions on the web? Thanks, DoranW
__________________
What I have: 1990 Red Mustang 5.0 LX: [BBK X-Pipe]-[MAC Cat-Back Exhaust] [MAC Cold Air Intake]-[BBK Equal Shorties] [3.55 Gears]-[Cobra Intake Manifold (Upper and Lower] [E-303 Cam]-[Granetelli Mass Air Flow Sensor] [Front and rear sway bars]-[New black carpet and seats.] [Adjustable Fuel Regulator]-[T5 Conversion w/ K. Cobra Clutch/Hurst STS] [Cobra Throttle Body]-[130A Alt. Conversion] Thinking about: Aftermarket Heads! Vortech A-Trim |
03-19-2002, 01:49 PM | #2 |
Moderator
Join Date: Mar 2001
Location: Myrtle Beach SC
Posts: 1,643
|
I have done all of the above and it can be a headache if you have never tackled anything like it. You can do it however if your patient and use good instructions. I think you could probably buy a service manual for your car. It has a pretty detailed tear down and rebuild of and entire car. With a little common sense and by reading everything carefully you should have no problems. I am assuming that the motor is in the car. It will be a little harder doing it this way but it can be done. Be sure and read the instructions closely and follow the torque specs and you should be fine.
Brad
__________________
1990 GT, 347, TFS TW Heads, TFS Cam, TFS Track heat, Twin turbos, FMIC, T5. Built Ford Tough Moderator |
03-19-2002, 02:05 PM | #3 |
Registered Member
Join Date: Jul 2001
Location: Seattle, WA
Posts: 381
|
About how long would you guess would it take to tackle the whole project? Like 40 hours? More/less?
Thanks, DoranW
__________________
What I have: 1990 Red Mustang 5.0 LX: [BBK X-Pipe]-[MAC Cat-Back Exhaust] [MAC Cold Air Intake]-[BBK Equal Shorties] [3.55 Gears]-[Cobra Intake Manifold (Upper and Lower] [E-303 Cam]-[Granetelli Mass Air Flow Sensor] [Front and rear sway bars]-[New black carpet and seats.] [Adjustable Fuel Regulator]-[T5 Conversion w/ K. Cobra Clutch/Hurst STS] [Cobra Throttle Body]-[130A Alt. Conversion] Thinking about: Aftermarket Heads! Vortech A-Trim |
03-19-2002, 04:05 PM | #4 |
Moderator
Join Date: Mar 2001
Location: Myrtle Beach SC
Posts: 1,643
|
I would say that if you have all the parts ready before you start, you could do it in a few days after work or school. I'd say 20 hours of actual work shoud get it done. But as with any project, count on twice as much time and three times the mony to get it done.
Brad
__________________
1990 GT, 347, TFS TW Heads, TFS Cam, TFS Track heat, Twin turbos, FMIC, T5. Built Ford Tough Moderator |
03-19-2002, 06:47 PM | #5 |
Registered Member
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
|
I swapped my heads and intake about two weeks ago...It took me all day Saturday and half of Sunday to tear it down and get it back together.
I highly reccomend doing it yourself once you learn how to do it you never have to pay for labor again. By far the hardest thing to me was swapping my gears from 2.73's to 3.73's.........It was a pain in the @ss to get just the right backlash. Good luck, Later
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Best heads, intake, cam setup?? | project 5.0 | Windsor Power | 11 | 02-25-2003 07:48 PM |
Heads, Intake | OneBad95 | Windsor Power | 0 | 07-22-2002 12:05 AM |
Cobra Heads And Intake Swap | surfbeast | Modular Madness | 1 | 03-12-2002 05:41 PM |
GT-40P heads and intake question | ex-lt1-guy | Windsor Power | 1 | 03-12-2002 09:55 AM |
It's May, still no new heads or intake by other manufacturers? | Red Mustang Gt 46 | Modular Madness | 7 | 05-08-2001 05:22 PM |