MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Modular Madness
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 05-31-2000, 11:31 PM   #1
Hammer
AKA "Dr. Evil"
 
Hammer's Avatar
 
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
Cool Reliable Zex nitrous results are in!!

And they're not too bad...

ET before Zex and X-pipe:
14.97 at 94.02

ET after:
14.18 at 100.02

Gain of .79 seconds and 6 MPH

Hope this helps...

------------------
98 GT
Bassani X-pipe, Dyno-Max Cat backs, 3.73 gears, Steeda shifter, FMS pullies, 87mm MAF, Roush cold air kit, Eibach springs, and Zex 75 shot
Hammer is offline   Reply With Quote
Old 06-01-2000, 10:26 AM   #2
Red94Z
Registered Member
 
Join Date: Apr 2000
Location: Ohio
Posts: 15
Post

Impressive.
Thanks for posting the results.
Something I'll have to look into for the 'lil GT
Red94Z is offline   Reply With Quote
Old 06-02-2000, 01:27 PM   #3
paver one
Registered Member
 
Join Date: Jan 2000
Location: Ogden Utah
Posts: 58
Cool

Read the March issue of MM & FF. They installed the ZEX system on a GT and got an additional 70 rwhp. I run the 75HP ZEX juice on a 1996 s281 SALEEN and love it.....

------------------
paver one is offline   Reply With Quote
Old 06-03-2000, 12:22 AM   #4
Cobra98conv
Registered Member
 
Join Date: Jan 2000
Location: Fort Wayne, IN
Posts: 9
Post

Looks good!

I'm ordering a ZEX system for my Cobra this week (with wife's approval even). Actually I can't wait.

I figure a 75 shot will hurl me well into 12s.

How long was the install?

------------------
1998 Triple blk Cobra Convertible
4.10 gears, ASP pullies, Bassanni X-pipe, Steeda subframe , Tri-Ax shifter, UPR Powerpipe, 80mm Pro-M
Best ET 13.59 @ 103.2mph (2.1 60')
Cobra98conv is offline   Reply With Quote
Old 06-06-2000, 02:11 PM   #5
paver one
Registered Member
 
Join Date: Jan 2000
Location: Ogden Utah
Posts: 58
Cool

It took me a couple of hours to install with having to route the line from the bottle in the trunk to the engine compartment. Also check to see if you can put a couple of thin washers on either side of the injector nozzle that goes into the air intake. I didn't like the idea of tightening the fittings onto rubber.....Good luck, let me know how it goes........

------------------
paver one is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Pathetic dyno results, NA vs nitrous fiveohpatrol Windsor Power 7 09-30-2002 01:05 PM
My Norwalk Nitrous results - time to rebuild the rear end! Mike Souslin Windsor Power 6 07-18-2002 09:31 PM
Comments on this Nitrous System 93boss Windsor Power 3 03-20-2002 05:19 PM
WOO HOO! RAN NITROUS AT TRACK! (long, real long) bark3rd Modular Madness 26 08-20-2001 08:05 AM
I need a crash course in NITROUS ED Dark_5.0 Windsor Power 7 07-12-2001 06:03 PM


All times are GMT -5. The time now is 03:13 AM.


SEARCH