![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Aug 2003
Location: rochester, ny
Posts: 31
|
![]() i have a speed density 88...........instead of buying a mass air conversion kit i was thinking of going to a dual 500cfm double pumper set up...........keep in mind the block is bored .030 over. what would give me better times in the 1/4? 3.73 rearend, tied frame, titanium drive shaft, block bored to .030, 1.94/1.60 valves....Also what cam should I upgrade to??? X, B, M, F, E???
I am also upgrading the valves to 2.02/1.60 |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Aug 2003
Location: rochester, ny
Posts: 31
|
![]() ????
__________________
![]() |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
|
![]() Bad idea. Your car would run worse with that set up. The speed density set-up will easily operate the mods you suggested.
BTW. If you have stock heads putting bigger valves doesnt do much for performance. Buy some GT-40P heads for about 300 bucks and slap those on with a good port job. As fas a s a cam goes the B or E cam would be best if you are going to go with an alphabet cam. If you are dead set on going with a carb a 600 cfm carb is all you would need to get the most out of your combo. It only cost about 200 bux to switch over to mass air. All you need is an ecu wich is a 5 minute install. A pig tail harness for the mass air sensor wich is a 15 minute install and a mass air sensor wich is a 5 minute install.
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Aug 2003
Location: rochester, ny
Posts: 31
|
![]() the heads are gt 40 heads.........and where can i get the mass air for 200???? ive looked on ebay, used places, new places and basically all over for the damn thing and the cheapest I found it was around 275 with everything........
__________________
![]() |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Nov 2003
Location: Philadelphia, MS
Posts: 191
|
![]() I'd suggest MAF conversion and an E cam.
The car should be consistent, reliable, and run like a scalded dog ![]() -Will
__________________
I'm just a guy who has nothing better to do, and loves his stangs. -Will |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Opinions? | KiltedBanshees93GT | Windsor Power | 13 | 09-19-2004 05:16 PM |
Looking for opinions... | Fox Body | Blue Oval Lounge | 11 | 01-09-2003 08:57 AM |
Opinions on engine set-up | 90lxracer | Windsor Power | 8 | 10-11-2002 08:21 PM |
EVERYONE! Need YOUR Opinions | Kevin Price | Blue Oval Lounge | 42 | 04-26-2001 10:49 AM |
Opinions on converting to c4 | Five0 | Windsor Power | 9 | 03-01-2001 09:49 PM |