![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Mar 1999
Location: Amarillo, Texas, USA
Posts: 780
|
![]() Slowly but surely, the engine is approaching completion. Shortblock, heads and valvetrain are complete. Should get to set it in for fitup next week. Here's some pics I took tonight after finishing the heads.
__________________
1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. |
![]() |
![]() |
![]() |
#2 |
black and blue
Join Date: May 2005
Location: cinci.
Posts: 84
|
![]() looks good, good luck with it
![]()
__________________
'93 3.0L SHO 5spd. '89 5.8L lx 5spd. 351W(349hp/384tq)-tfs twisted wedge(stage 2), rpm air-gap, comp cam(294/294:518/518) and lifters, kb .060 pistons(11.5:1), mac shorties, pypes o/r X, mac 2.5" all the way back, holley 750, march u/d pulleys...it's alive..it's back together and running strong -zach |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
![]() What is it?
__________________
![]() |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 1999
Location: Amarillo, Texas, USA
Posts: 780
|
![]() Sorry, I forget these things sometimes. It's a '71 351 Cobra Jet (Cleveland), 4bbl. This time I went with a hydraulic roller cam.
So far, here's what's either in it or on the shelf waiting to go on it. 351C, .030 over Probe forged pistons with a 13cc dish cut into them Total seal gapless rings stock crank and rods, rotating assenbly balanced Comp cams, hyd roller .579/.588 @ 224/230 deg.@.050 Comp cams beehive strings Manley stainless, swirl polished valves with comp 10 deg. retainers 3 angle valve job block milled .010, heads milled .020 4bbl heads w/ 67 cc chambers Pocket porting, with short radius work CPR custom made long tubes (for fox body) Canton 7 qt oil pan for Fox body Oh. . and a Tuff Stuff chrome water pump.. . hey, if it don't go, chrome it. I also have a new tremec TKO600 to bolt up to it. Auburn street posi with 31 spline Moser axles but don't know what gears to go with yet.
__________________
1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. |
![]() |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]() ![]() |
![]() |
![]() |
#6 |
Guest
Posts: n/a
|
![]() ![]() |
![]() |
![]() |
#7 |
Guest
Posts: n/a
|
![]() looks sweet
|
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
1968 engine numbers, 289 or 302? | andybud | Classic Mustangs | 5 | 09-11-2003 12:14 PM |
New engine pics, what do you think? | QuantumMotorsports | Windsor Power | 10 | 08-31-2003 07:50 PM |
raced a Supra Twin Turbo | Stang35th | Stang Stories | 63 | 08-23-2003 12:36 AM |
Rebuilt Engine Problems | sleeperstang | Classic Mustangs | 6 | 05-08-2003 10:19 AM |
Very bad experience with Engine Dynamics of San Jose CA | JAGraff | Racer's Club House | 0 | 05-12-1999 02:27 AM |