© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-06-2002, 07:26 PM | #1 |
Trisket
Join Date: May 2002
Location: University of Florida, FL Posts: ½
Posts: 1,560
|
arrrrg! ...they sent me the wrong part!
im installing XM radio this weekend but crutchfield sent me the u-ring tools to remove my mach460....my headunit isnt the same as the old mach460 model...my releases are on the bottom, not the sides....looks like im going to ford tomorrow morning and driving with a half popped headunit til i set up the XM...wee...
anyone have any experience with removing the new ones? have any advice with talking to ford about pulling that out?....just hoping for a little feedback about it... thanks jonathon
__________________
University of Florida - Physics Major My 02GT vert Media Center Pics BBK Underdrive Pulleys | K&N FIPK (Gen II) | Bullet Grille | Mach 1 Chin Spoiler | UPR Interior Parts | XM Radio | Audiobahn Subs Ricer Hater's Club Member #1/2 (30) http://www.ricehatersclub.com/ |
12-06-2002, 07:34 PM | #2 |
Registered Member
Join Date: Aug 1999
Location: Las Vegas, NV
Posts: 202
|
I may be wrong but...
I thought that any automotive parts store sold those "radio remover keys"? I thought they were just some "allenwrench" looking things (that could easily be replaced with a metal clothes hanger) that you stuck in each hole to release the holding clips...? If I'm wrong, then nevermind... |
12-06-2002, 08:36 PM | #3 |
Registered Member
Join Date: Oct 2001
Location: Florida Keys
Posts: 593
|
small philips screwdrivers worked for me
__________________
89 notch-finally not stock!! ported gt40's, ported cobra intake, 65mm tb, 75mm maf, mac cai, lt's,prochamber, fms 1.6 rr, 125 shot. |
12-06-2002, 09:24 PM | #4 |
Trisket
Join Date: May 2002
Location: University of Florida, FL Posts: ½
Posts: 1,560
|
its not the two holes on each side of the headunit...there are 6 holes on the bottom lip....theyre a different design hole too...i guess ill just bug ford in the AM...lol
__________________
University of Florida - Physics Major My 02GT vert Media Center Pics BBK Underdrive Pulleys | K&N FIPK (Gen II) | Bullet Grille | Mach 1 Chin Spoiler | UPR Interior Parts | XM Radio | Audiobahn Subs Ricer Hater's Club Member #1/2 (30) http://www.ricehatersclub.com/ |
12-08-2002, 03:17 AM | #5 |
Trisket
Join Date: May 2002
Location: University of Florida, FL Posts: ½
Posts: 1,560
|
for anyone wondering...
it turns out the new systems dont come out like normal....all you need to do it pry out the console around the gearshifter, then the console around the A/C,headunit, etc controls...its held in by metal clips...they just pop out...then there are two bolts that hold in the headunit....simple as that.... the install went smoothly and the XM radio is awesome ...i didnt even mount the antenna..its in my trunk..hehe
__________________
University of Florida - Physics Major My 02GT vert Media Center Pics BBK Underdrive Pulleys | K&N FIPK (Gen II) | Bullet Grille | Mach 1 Chin Spoiler | UPR Interior Parts | XM Radio | Audiobahn Subs Ricer Hater's Club Member #1/2 (30) http://www.ricehatersclub.com/ |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TFI module part # | GhettoPop | Windsor Power | 2 | 02-12-2004 01:34 PM |
How can I tell if a part will pass emmisions? | Kamaro Killer | Windsor Power | 2 | 09-08-2002 07:05 PM |
Looking for Bosch part #'s! | chris91LX | Windsor Power | 0 | 12-28-2001 06:58 PM |
Is This Wrong to do? | RedLilPony | Blue Oval Lounge | 15 | 05-02-2001 01:02 AM |
Hard to locate part for 83 stang help!!! | 83stanger | Small Ponies | 0 | 03-02-1999 08:52 AM |