MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Website Community > Blue Oval Lounge
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 09-09-2001, 12:42 AM   #1
tireburner163
It's a lot like a race car
 
tireburner163's Avatar
 
Join Date: Aug 2000
Location: Meridian, MS
Posts: 4,130
Post which engine turbo 2.3 or 5.0

I can't decide which to swap in a turbocharger 2.3 liter or a 5.0 liter. Which do you guys think would be better/cheaper. I'm worried about swaping in the eletronics from the 2.3 turbo(I HATE running wires). Much of the wiring hassel could be elinated if I went with a carbed 5.0 liter. But some one told me that swaping in a 2.3 turbo would be cheaper. Also I've heard that the front syspention is different on a 4 banger than on a V-8(bigger brakes and fatter sway bars). Is this true?

------------------
THE SLO PONY
1992 Ford Mustand LX. 2.3 liter four-banger, auto. Future mods: V-8 swap.

If it ain't broke, you ain't tryin hard enough
tireburner163 is offline   Reply With Quote
Old 09-09-2001, 01:37 AM   #2
Unit 5302
Registered Member
 
Join Date: May 1999
Posts: 5,246
Post

The Turbo 2.3L is good for 175hp in 1987-1988 Thunderbird TC's and the Merkur XR4Ti. The Mustang SVO version got 205hp.

Modifications to the turbo setup are possible, but to get more than about 240hp, you'll need to do some turbo upgrading, or go to nitrous. I don't know as I'd want to run the stock T-5 4banger beyond that, and the rear end starts to become a little iffy as well. Don't expect to get away without making cooling system mods for the turbo engine either. They kick out a ton of heat, and the intercoolers in there add to the need for cooling.

The 5.0L everybody knows about. Expect to make a couple more changes with the 5.0L, but not many.

Before anybody babbles about reliability, the turbo 2.3L is built to take serious abuse. Forged crank, rods, pistons.
Unit 5302 is offline   Reply With Quote
Old 09-09-2001, 02:16 AM   #3
tireburner163
It's a lot like a race car
 
tireburner163's Avatar
 
Join Date: Aug 2000
Location: Meridian, MS
Posts: 4,130
Post

does anyone know of a company that sells a kit for a V-8 conversion.

------------------
THE SLO PONY
1992 Ford Mustand LX. 2.3 liter four-banger, auto. Future mods: V-8 swap.

If it ain't broke, you ain't tryin hard enough
tireburner163 is offline   Reply With Quote
Old 09-09-2001, 03:05 AM   #4
1965GTO
Registered Member
 
Join Date: Jul 2001
Location: Dupo,ill
Posts: 219
Post

You can build a 225horse 2.3 without nitrous. Call esslinger Ph. 888-444-4919. Buddy Ingersoll use to run low 10's in the 1/4 mile in the 70's with a carbuereted 2.0 turbo pinto.

------------------
1965GTO is offline   Reply With Quote
Old 09-09-2001, 03:22 AM   #5
84_GT350
Registered Member
 
Join Date: Apr 1999
Location: Overland Park, KS, USA
Posts: 1,631
Post

Kaufmann Products makes a good 4 cyl. to V8 swap kit.

------------------
1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s

So I pushed it up to 110,
That flathead motor was about to give in,
I crossed my fingers and prayed to the lord,
Don't let me down you fuct up ford!"

"5-Oh Ford" by The Reverend Horton Heat
84_GT350 is offline   Reply With Quote
Old 09-09-2001, 11:28 AM   #6
Unit 5302
Registered Member
 
Join Date: May 1999
Posts: 5,246
Post

Quote:
Originally posted by 1965GTO:
You can build a 225horse 2.3 without nitrous. Call esslinger Ph. 888-444-4919. Buddy Ingersoll use to run low 10's in the 1/4 mile in the 70's with a carbuereted 2.0 turbo pinto.
You don't need help to get a 2.3L intercooled turbo to 225hp. All you need is a chip to up the boost level a little and good exhaust. Maybe a couple SVO parts.

There's a guy a few years ago running 10's/11's in the quarter with a 2.3L Turbo Pinto He got the engine out of a Turbo Coupe, had upgraded turbo's in it, the car was stripped, ran full out drag slicks, and a big *** shot of NOS. The race weight on that car was probably about 1000lbs less than what tireburner's would be.
Unit 5302 is offline   Reply With Quote
Old 09-11-2001, 12:57 AM   #7
1965GTO
Registered Member
 
Join Date: Jul 2001
Location: Dupo,ill
Posts: 219
Post

I said 225hp 2.3 without nos and also without a turbo.
1965GTO is offline   Reply With Quote
Old 09-11-2001, 01:58 AM   #8
Unit 5302
Registered Member
 
Join Date: May 1999
Posts: 5,246
Question

Just read your entire post, nothing about without a turbo? Are you saying it will do it N/A??? LOL.

Getting 225hp out of a turboed 2.3L is easy. Once again, you don't need somebody else's help to do it. Buy a chip (which will raise the psi), get a good exhaust, and a good induction. Maybe an SVO intake, 225 is pretty easy to come by. The SVO made 200 stock.
Unit 5302 is offline   Reply With Quote
Old 09-11-2001, 05:00 AM   #9
PKRWUD
Junior Member
 
PKRWUD's Avatar
 
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
Post

Unit-
I've seen it done.

BTW, I just was reading the latest SEMA mag, and there's a guy in there who used to run Hondas, but now has a FWD Focus with a DOHC 2.0L engine that is N/A, non-NOS, putting out over 600hp. He says it's all in the heads. Before this latest head, he was turning low 10's @ 124 mph (400 hp with the "old" head).

**** like that just plain scares me.

Take care
~Chris

P.S. The old 2000cc Pinto engines can take much higher rpms than the 2.3L, and were the top choice of Pony Stock racers until the supply dried up.

------------------
Retired Moderator
MustangNet

My site: JimPorterRacing

RACECAR spelled backwards is RACECAR

HEY !!! Are you ASE Certified ??? If you are, ask me about iATN. The best tool you'll ever have, and it's free !!!
PKRWUD is offline   Reply With Quote
Old 09-11-2001, 01:06 PM   #10
Unit 5302
Registered Member
 
Join Date: May 1999
Posts: 5,246
Post

I didn't say it's impossible to get 225hp N/A with a 2.3L, but you'd be very hard pressed to do so.

Bottom line is crank, rods, pistons, head, cam, exhuast, and intake. If you want to get 225hp N/A from a 2.3L it would cost 10x what a Turbo Coupe engine would.

The aftermarket hasn't typically catered to the 2.3L N/A engine that I've ever seen. In stock form the 2.3L is a huge turd. The most powerful 2.3L N/A engine from Ford that I know of made 105hp.

I don't see any realism in comparing the first Domestic mass produced SOHC engine ever (2.3L) to a much newer and superior 2.0L DOHC engine. That's on a par with comparing a 5.0 to a 4.6 DOHC. It's not hard to see which one has more potential. Even though the 5.0 is a damn good engine, and it's proved it clear up to a high rpm racing level, the 4.6L DOHC will outrev, and out hp the 5.0.

Getting 600hp N/A out of a 2.0L? What's he spin it to? 20,000rpms? He'd need over 150lb/ft of torque, even there. I'm sorry, but I have to call BS on that. No way. Not even a 2 stroke pulls that kind of number. You're talking literally over 300hp/liter, N/A. I don't care where his car was dyno'd. That equates to an N/A 1500hp+ 5.0, or 1400hp 4.6L N/A.
Unit 5302 is offline   Reply With Quote
Old 09-11-2001, 08:55 PM   #11
1965GTO
Registered Member
 
Join Date: Jul 2001
Location: Dupo,ill
Posts: 219
Post

Well call Esslinger and find out if interested. I don't think they are that expensive as they are fairly common on dunebuggies in California and other places.
1965GTO is offline   Reply With Quote
Old 09-12-2001, 01:54 AM   #12
myred86gt
Registered Member
 
Join Date: Sep 2001
Posts: 17
Post

I owned an 88 t'bird t-coupe. It pulled har-
der than a stock 5.0. Everything was stock
except the exaust and a minor modification
to Fords terrible boost management:
take a trip to the hardware store and buy a
t-valve with pressure fittings and some hose.
Bypass the boost control solenoid with the
valve and voila, 18 pounds of boost from
2600rpm on up until fuel starvation from the
stock pump and injectors. This will yield up
to 265 hp, to go crazier, buy the motorsport
rollercam setup, 3.5 inch turbo exhaust out-
let and downpipe, oilcooler, bigger injectors, get rid of the stock airbox and
install k+n cone filter at maf-box. last but
not least a reprogrammed ECU, superchips is
very good with Bosch based engine management
------------
myred86gt is offline   Reply With Quote
Old 09-12-2001, 02:01 AM   #13
Unit 5302
Registered Member
 
Join Date: May 1999
Posts: 5,246
Post

Quote:
Originally posted by myred86gt:
I owned an 88 t'bird t-coupe. It pulled har-
der than a stock 5.0. Everything was stock
except the exaust and a minor modification
to Fords terrible boost management:
take a trip to the hardware store and buy a
t-valve with pressure fittings and some hose.
Bypass the boost control solenoid with the
valve and voila, 18 pounds of boost from
2600rpm on up until fuel starvation from the
stock pump and injectors. This will yield up
to 265 hp, to go crazier, buy the motorsport
rollercam setup, 3.5 inch turbo exhaust out-
let and downpipe, oilcooler, bigger injectors, get rid of the stock airbox and
install k+n cone filter at maf-box. last but
not least a reprogrammed ECU, superchips is
very good with Bosch based engine management
------------
I also had a Thunderbird Turbo Coupe with a 5spd. It was quick for what it was, but it's limiting quickly surfaced around 80mph. The gearing no longer was able to cover up from a lack of hp vs my 87 and 88GT. The T-Bird TC made 175hp stock with a 3600-3700lb curb weight. That's 50hp short, and 500lbs heavy. The TC was not a match for the Fox 5.0HO's. Not even close. Even with 250hp they would be outclassed by a good driver in a 5.0.
Unit 5302 is offline   Reply With Quote
Old 06-16-2009, 10:30 PM   #14
Lazypig
Registered Member
 
Join Date: Jun 2009
Posts: 1
Default Re: which engine turbo 2.3 or 5.0

I own a 2.3 turbo and a 5.8w the 2.3 makes 300hp esslinger pistons and ported intake thats it.
Lazypig is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Very bad experience with Engine Dynamics of San Jose CA JAGraff Classic Mustangs 8 06-16-2005 11:43 AM
Engine transplant across decades and models. Sketch Classic Mustangs 6 04-18-2004 07:51 AM
Turbo vs SC Sounds like good advice mustardjohn Small Ponies 0 11-16-2003 05:21 PM
Rebuilding an engine.. and then some Halz Windsor Power 5 04-01-2002 02:01 AM
pulled engine....pulled out wallet....a true story! 84LX89GT Windsor Power 6 03-13-2002 03:04 PM


All times are GMT -5. The time now is 11:39 PM.


SEARCH