Throwout Bearing Blues

Rstng93 · 06-17-2004, 10:25 AM

Hey guys i have been having a problem with the throwout bearing on my 89 Mustang 5.0. Every time I install a new bearing, it is quiet for a few hours and then starts making a squealing noise. This noise occurs when the car is in gear, or in neutral, and the clutch is released. The second I put a little bit of pressure on the clutch, the noise stops. I have replaced the bearing four times, and i have replaced every other part in there. I have a new pilot bearing, new: flywheel, clutch, pressure plate, fork, pivot, 4 throwout bearings, and i even put in a new rebuilt transmittion in yesterday. The noise persists. And today i noticed that it is making a rattling noise too. I am so frustrated over this problem. If any of you guys have had this problem before, or know what could be causing this problem, i would really appreciate your help. Thanks.

429mustang · 06-18-2004, 03:20 PM

Did you grease the bearing and is the bearing retainer shaft (whatever it's called, the tubular surface the bearing rides on) in good condition? Maybe see if you can get a different brand bearing somewhere else????

LX5liter · 06-19-2004, 08:41 PM

Is the clutch adjusted properly? If it is always partially dis-engaged the bearing will wear pre-maturely.

06-17-2004, 10:25 AM	#1 (permalink)
Rstng93 Registered Member Join Date: Jun 2002 Location: Orlando Fl Posts: 7	Throwout Bearing Blues Hey guys i have been having a problem with the throwout bearing on my 89 Mustang 5.0. Every time I install a new bearing, it is quiet for a few hours and then starts making a squealing noise. This noise occurs when the car is in gear, or in neutral, and the clutch is released. The second I put a little bit of pressure on the clutch, the noise stops. I have replaced the bearing four times, and i have replaced every other part in there. I have a new pilot bearing, new: flywheel, clutch, pressure plate, fork, pivot, 4 throwout bearings, and i even put in a new rebuilt transmittion in yesterday. The noise persists. And today i noticed that it is making a rattling noise too. I am so frustrated over this problem. If any of you guys have had this problem before, or know what could be causing this problem, i would really appreciate your help. Thanks.

06-18-2004, 03:20 PM	#2 (permalink)
429mustang Registered Member Join Date: May 2001 Location: westerville, OH USA Posts: 618	Did you grease the bearing and is the bearing retainer shaft (whatever it's called, the tubular surface the bearing rides on) in good condition? Maybe see if you can get a different brand bearing somewhere else???? __________________ 1990 Notchback: BBK Ceramic Coated Full length headers, Dr. Gas 3"- 2 1/2" x-pipe, Flowmaster 40's/turndowns.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
clutch and throwout bearing questions	bmxmon	Classic Mustangs	0	05-23-2004 05:32 PM
T5 throwout bearing chirp..Argh	squid	Windsor Power	1	09-20-2002 09:37 PM
Need advice on throwout bearing	RPM427	Windsor Power	2	08-28-2002 03:05 PM
throwout bearing noise!!	Coupe5oh	Windsor Power	1	04-30-2002 06:38 PM
is it the throwout bearing?	stanger8172	Windsor Power	3	07-22-2001 10:06 AM

06-19-2004, 08:41 PM	#3 (permalink)
LX5liter dude5l Join Date: May 2001 Location: Grande Prairie, Alberta, Canada Posts: 603	Is the clutch adjusted properly? If it is always partially dis-engaged the bearing will wear pre-maturely.

Sponsored Links