Dyno results

7up · 08-11-2002, 08:30 PM

I went to thye dyno on Saturday and I was extremely suprised by my results. I had 299.3 rwhp and 355.5 torque. I will try and scan and post my dyno sheet soon.

Stang Runner · 08-11-2002, 09:17 PM

Nice nice I want to see it Hope you can get it on the PC

Skyman · 08-12-2002, 01:01 AM

What kinda dyno and what are ur track times?

Skyler

7up · 08-12-2002, 01:24 AM

I haven't run it at the track yet. I'm not sure what kind of dyno it was. It was done at dyno-pro in Denver. I just looked on the web site at dynopro.com and it is a dyno jet 248c. They corrected the hp and torque for sea level.

On another note my car just got backed up into by a f**** Suburban and dented the hell out of the drivers side door and fender. The car took off. I'll go more in depth in Blue Oval.

08-11-2002, 08:30 PM	#1
7up Registered Member Join Date: Feb 2002 Location: Greeley, Colorado Posts: 321	Dyno results I went to thye dyno on Saturday and I was extremely suprised by my results. I had 299.3 rwhp and 355.5 torque. I will try and scan and post my dyno sheet soon. __________________ 91 lx convertible, Vortech a-trim, 2.87 blower pulley. 30lb injectors, 80 mm mass air, 255 fuel pump, flowmaster cat back, bbk long tubes and h pipe 299.3 hp, 355.5 tq(before h-pipe, headers) Ricer Hater's Club-member #16

08-11-2002, 09:17 PM	#2
Stang Runner Registered Member Join Date: Jun 1999 Location: Walker, MI, USA Posts: 1,202	Nice nice I want to see it Hope you can get it on the PC __________________ Engine: steel mounts, Under drive pulleys, K&N, GT-40 Intake ported Lower, No power steering, No A/C, Mac cold intake, 65MM TB, 255 Fuel pump, 24's, AFR 165 58cc, Rocker Arms 1.7with the stock Cam, 1 5/8 short headers, offRoad X-pipe Drive Train: 3.55, T-5 with a Pro 5.0 shifter 12.656@107.71MPH See It at www.T-racing.com/mustang.htm

08-12-2002, 01:01 AM	#3
Skyman I need 110mph Trap Speed! Join Date: Feb 1999 Location: So, CA Posts: 4,315	What kinda dyno and what are ur track times? Skyler __________________ 2001 BMW M3 6spd 12.79@108 RIP ---- 1993 Notch w/ 98 4V 4.6 Fasttt... -1989 Saleen Mustang #406- 12.32@109 -1999 Black Cobra Coupe- JBA Shorties, Bassani Cat-X, Magnaflow 3", Pulleys, 85mm Pro-M, Ported Intake, Soild Rear w/ 4.30s, Tubular Front End, X2C arms, 13lb batt, few others.

08-12-2002, 01:24 AM	#4
7up Registered Member Join Date: Feb 2002 Location: Greeley, Colorado Posts: 321	I haven't run it at the track yet. I'm not sure what kind of dyno it was. It was done at dyno-pro in Denver. I just looked on the web site at dynopro.com and it is a dyno jet 248c. They corrected the hp and torque for sea level. On another note my car just got backed up into by a f**** Suburban and dented the hell out of the drivers side door and fender. The car took off. I'll go more in depth in Blue Oval. __________________ 91 lx convertible, Vortech a-trim, 2.87 blower pulley. 30lb injectors, 80 mm mass air, 255 fuel pump, flowmaster cat back, bbk long tubes and h pipe 299.3 hp, 355.5 tq(before h-pipe, headers) Ricer Hater's Club-member #16

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
331 Dyno results	302 LX Eric	Windsor Power	12	04-29-2004 10:13 PM
you will NOT believe this... dyno results	fiveohpatrol	Windsor Power	27	11-27-2001 02:53 PM
DYNO results, and questions	mmike	Windsor Power	7	09-24-2001 09:11 PM
Dyno results inside with timing adjuster installed	Mustang92	Modular Madness	7	02-20-2001 09:24 PM