drag launch air bag

WADS56 · 05-09-2001, 01:58 AM

How much psi do you guys run in it at the strip?

------------------
347 W/ A-trim 6#'s, Canfield heads, out of the box Systemax II intake, solid roller cam. 11.1 @123mph

93lx 5.0 daily driver

Rick 91GT · 05-09-2001, 11:54 AM

You only need to run enough air to make it leave straight, with your setup try 12psi and go from there in 1/2 or 1lb increments. I was running 11psi with my old set-up with this one I plan on starting at 12psi and going from there if I have problems. I brought the sir fitting up inside the car and out the plastic panel in the back then I have easy access, I had it inside the plastic panel, right next to the shock but it was awkward to get a tire gauge in there.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!

[This message has been edited by Rick 91GT (edited 05-09-2001).]

WADS56 · 05-09-2001, 10:35 PM

Thanks Rick, I'll try 12 lbs.

05-09-2001, 01:58 AM	#1
WADS56 gear banger Join Date: Aug 2000 Location: CHICAGO Posts: 1,144	drag launch air bag How much psi do you guys run in it at the strip? ------------------ 347 W/ A-trim 6#'s, Canfield heads, out of the box Systemax II intake, solid roller cam. 11.1 @123mph 93lx 5.0 daily driver

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ques. about Drag launch springs	skiwesser	Windsor Power	1	06-22-2004 10:06 PM
Eibach Drag Launch Kit	bigred90gt	Windsor Power	5	06-21-2003 02:40 PM
Springs--4cyl or Drag Launch	kevknotch88	Windsor Power	1	10-26-2001 06:19 AM
Eibach Drag Launch Springs	glxstang	Windsor Power	14	08-10-2001 01:12 AM
car looks like 4x4 after drag launch springs	WADS56	Blue Oval Lounge	6	05-13-2001 02:04 AM

05-09-2001, 11:54 AM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	You only need to run enough air to make it leave straight, with your setup try 12psi and go from there in 1/2 or 1lb increments. I was running 11psi with my old set-up with this one I plan on starting at 12psi and going from there if I have problems. I brought the sir fitting up inside the car and out the plastic panel in the back then I have easy access, I had it inside the plastic panel, right next to the shock but it was awkward to get a tire gauge in there. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! [This message has been edited by Rick 91GT (edited 05-09-2001).]

05-09-2001, 10:35 PM	#3
WADS56 gear banger Join Date: Aug 2000 Location: CHICAGO Posts: 1,144	Thanks Rick, I'll try 12 lbs.