Ring and Pinion 373's

roadrunner93 · 01-22-2001, 03:57 PM

A buddy of mine found a set of 373's at an auto salvage. When he went over to pick them up, they tried to sell them to him without the pinion. When he asked where it was, they said you can use the same pinion that is in the car now (He has 273's). I've never heard of that before, so he obviously didn't buy them.
Anyways, the salvage place called him back an hour later and said they found one. He thinks they are trying to rip him off. Are the pinions branded like the ring gear? How can you tell? Does the 273 pinion fit?

stanger8172 · 01-22-2001, 04:54 PM

What kind of car did you find 3.73's out of? How much did they ask for? I have turtle gears(2.73's) like you and will be looking for some gears too.

--------------
'91 LX ported,polished,and milled stock heads, 1.6rr, hardened pushrods and guide plates, 1.94/1.60 stainless valves, triple valve springs,electric fans, short belt, glasspacks

Josh91 · 01-22-2001, 05:20 PM

I think you need the pinion that came with the ring. Not only are there different numbers of teeth, but the wear pattern would be way off if you used a ring from one set and a pinion from another. I would not get them.

------------------
1991 Mustang GT - Cobra Intake, FMS 65mm TB, C&L 73mm MAF, GT-40P heads, Crane 2031 cam, Crane 1.7rr, Built AOD, Art Carr 2400 non-lockup converter, Transgo shift kit, BBK chrome cold air, FMS 'P' headers, Pacesetter off-road H, BBK aluminum pulleys, 2-C Flows w/ dumps, 4.10's, Steeda STB, for now...

The Original GT-40P Tech Page

70stang · 01-22-2001, 06:04 PM

To know if your pinion will work with the 3.73 ring, find out how many teeth your pinion has (I don't know off the top of my head). Then count the number of teeth on the ring. Divide the number of teeth on the ring by the number of teeth on your pinion and you should get 3.73. If you don't, then your pinion won't work with the gear.

However, I would not buy a ring and pinion seperately. As a matter of fact, I wouldn't buy a used ring and pinion unless I knew for sure it was a matched set because of the different wear patterns. If you do, then you will end up with lots of extra shavings in your rearend and the ring and pinion will wear out prematurely.

cojonepony · 01-22-2001, 09:26 PM

Beware of these kind of scoundrels!!! The pinion has markings on the head of which include the ratio. Also, dividing the # of ring gear teeth by the # of pinion gear teeth equals the ratio. Never mix and match an R&P set. In order to obtain max. life and tolerable noise levels you should stick with a new set. The FMS gears are reasonably priced and easiest to set-up.

roadrunner93 · 01-23-2001, 01:11 PM

Thanks guys. Stanger8172 The gears are out of a 92 LX that was rolled 5 or 6 times. He took almost all of the parformance parts off before it went to the salvage yard.

01-22-2001, 03:57 PM	#1
roadrunner93 Registered Member Join Date: Oct 2000 Location: Canada Posts: 65	Ring and Pinion 373's A buddy of mine found a set of 373's at an auto salvage. When he went over to pick them up, they tried to sell them to him without the pinion. When he asked where it was, they said you can use the same pinion that is in the car now (He has 273's). I've never heard of that before, so he obviously didn't buy them. Anyways, the salvage place called him back an hour later and said they found one. He thinks they are trying to rip him off. Are the pinions branded like the ring gear? How can you tell? Does the 273 pinion fit?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ring and pinion gear installation	chiaronate	Windsor Power	5	11-05-2002 07:47 PM
Ring and Pinion Install	Titan	Modular Madness	21	08-15-2002 10:06 PM
Mr. 5.0....ANYONE...HELP!!! RING PINION QUESTION!!!	90LxDroptop	Windsor Power	3	09-08-2001 02:01 PM
ring and pinion install	stanger8172	Windsor Power	5	03-25-2001 01:19 AM
Changing ring & pinion gear is illegal	Ripper	Modular Madness	1	04-06-2000 12:45 PM

01-22-2001, 04:54 PM	#2
stanger8172 Registered Member Join Date: Nov 2000 Location: Milwaukee,Wisconsin Posts: 380	What kind of car did you find 3.73's out of? How much did they ask for? I have turtle gears(2.73's) like you and will be looking for some gears too. -------------- '91 LX ported,polished,and milled stock heads, 1.6rr, hardened pushrods and guide plates, 1.94/1.60 stainless valves, triple valve springs,electric fans, short belt, glasspacks

01-22-2001, 05:20 PM	#3
Josh91 Registered Member Join Date: Nov 1998 Location: Salina, KS Posts: 83	I think you need the pinion that came with the ring. Not only are there different numbers of teeth, but the wear pattern would be way off if you used a ring from one set and a pinion from another. I would not get them. ------------------ 1991 Mustang GT - Cobra Intake, FMS 65mm TB, C&L 73mm MAF, GT-40P heads, Crane 2031 cam, Crane 1.7rr, Built AOD, Art Carr 2400 non-lockup converter, Transgo shift kit, BBK chrome cold air, FMS 'P' headers, Pacesetter off-road H, BBK aluminum pulleys, 2-C Flows w/ dumps, 4.10's, Steeda STB, for now... The Original GT-40P Tech Page

01-22-2001, 06:04 PM	#4
70stang Registered Member Join Date: Dec 2000 Location: Twelve Mile, IN USA 46988 Posts: 17	To know if your pinion will work with the 3.73 ring, find out how many teeth your pinion has (I don't know off the top of my head). Then count the number of teeth on the ring. Divide the number of teeth on the ring by the number of teeth on your pinion and you should get 3.73. If you don't, then your pinion won't work with the gear. However, I would not buy a ring and pinion seperately. As a matter of fact, I wouldn't buy a used ring and pinion unless I knew for sure it was a matched set because of the different wear patterns. If you do, then you will end up with lots of extra shavings in your rearend and the ring and pinion will wear out prematurely.

01-22-2001, 09:26 PM	#5
cojonepony Registered Member Join Date: Feb 2000 Posts: 132	Beware of these kind of scoundrels!!! The pinion has markings on the head of which include the ratio. Also, dividing the # of ring gear teeth by the # of pinion gear teeth equals the ratio. Never mix and match an R&P set. In order to obtain max. life and tolerable noise levels you should stick with a new set. The FMS gears are reasonably priced and easiest to set-up.

01-23-2001, 01:11 PM	#6
roadrunner93 Registered Member Join Date: Oct 2000 Location: Canada Posts: 65	Thanks guys. Stanger8172 The gears are out of a 92 LX that was rolled 5 or 6 times. He took almost all of the parformance parts off before it went to the salvage yard.