Aftermarket oil pans?

blue00gt · 07-18-2001, 03:43 PM

The oil pan on my 2000GT had a little mishap with the ground. Does anyone make a good aftermarket oil pan for the 4.6-2V? I called Moroso and they said they are probably about 6 mos. away from releasing one.

------------------
2000GT Atlantic Blue: Cobra R Wheels-17x9 255/40/17, 17x10.5 315/35/17, tubular K-member & control arms, Tokico 5-ways, coil overs, sway bars, strut/shock tower bars, 70mm FMS throttle body, Saleen nose.
79 Pace Car: Maximum Motorsports suspension - H&R Race springs, Bilsteins, rear control arms, chassis bracing, Draglites, 302 w/ Edelbrock Performer intake, cam and 600cfm carb, BBK equal-lengths & H-pipe, 2.5" Flowmaster 2chmbr exhaust, Al Driveshaft, 8.8 trak-loc, TCI C4 w/ 2000 stall, B&M

Ares · 07-18-2001, 05:00 PM

Yep your in luck, Canton Racing Products makes a very nice one that they also supply Ford with for the 2000 Cobra R.
P/N 15-784 baffled same as used on Cobra R
P/N 15-780 non baffled

They also make a screen/windage tray for the 4.6/5.4
P/N 20-939 4.6 tray
P/N 20-939C 5.4 tray used on Cobra R

(203)481-9460
Canton Racing Products
232 Branford Rd.
No. Branford, CT. 06471

------------------
2000 GT Laser red-5speed,MAC Cold Air, MAC 2 1/2" Cat-Back, 3.27gears, Pro-5.0 shifter, Weld Draglite's 15x5 and 15x10, 275/50-15 DragT/A's, 165R15 front, BBK Underdrive pullies, BBK offroad X-pipe with Dynomax super converters

Best Quarter mile run to date: 13.350@101.79/1.844 60'(7-6-01)Best MPH 101.79(7-6-01)

[This message has been edited by Ares (edited 07-18-2001).]

blue00gt · 07-19-2001, 10:59 AM

Thanks Ares, I'll check it out!

07-18-2001, 03:43 PM	#1
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	Aftermarket oil pans? The oil pan on my 2000GT had a little mishap with the ground. Does anyone make a good aftermarket oil pan for the 4.6-2V? I called Moroso and they said they are probably about 6 mos. away from releasing one. ------------------ 2000GT Atlantic Blue: Cobra R Wheels-17x9 255/40/17, 17x10.5 315/35/17, tubular K-member & control arms, Tokico 5-ways, coil overs, sway bars, strut/shock tower bars, 70mm FMS throttle body, Saleen nose. 79 Pace Car: Maximum Motorsports suspension - H&R Race springs, Bilsteins, rear control arms, chassis bracing, Draglites, 302 w/ Edelbrock Performer intake, cam and 600cfm carb, BBK equal-lengths & H-pipe, 2.5" Flowmaster 2chmbr exhaust, Al Driveshaft, 8.8 trak-loc, TCI C4 w/ 2000 stall, B&M

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AFtermarket or factory fender	7up	Windsor Power	13	08-19-2002 11:30 PM
Aftermarket 289/302 Water Necks	DJs350H	Classic Mustangs	8	05-12-2002 02:47 PM
Those with Vortech's and aftermarket deep sump pans come inside...	Nutty 5.0	Windsor Power	3	06-25-2001 08:35 PM
67 Convertible Floor Pans	Gichigumi	Classic Mustangs	0	06-14-2001 04:12 PM
Aftermarket 4.6 Heads & Manifolds & Blocks...WHERE ARE THEY!! got any ideas?	Shawn	Modular Madness	3	09-26-2000 02:07 PM

07-18-2001, 05:00 PM	#2
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	Yep your in luck, Canton Racing Products makes a very nice one that they also supply Ford with for the 2000 Cobra R. P/N 15-784 baffled same as used on Cobra R P/N 15-780 non baffled They also make a screen/windage tray for the 4.6/5.4 P/N 20-939 4.6 tray P/N 20-939C 5.4 tray used on Cobra R (203)481-9460 Canton Racing Products 232 Branford Rd. No. Branford, CT. 06471 ------------------ 2000 GT Laser red-5speed,MAC Cold Air, MAC 2 1/2" Cat-Back, 3.27gears, Pro-5.0 shifter, Weld Draglite's 15x5 and 15x10, 275/50-15 DragT/A's, 165R15 front, BBK Underdrive pullies, BBK offroad X-pipe with Dynomax super converters Best Quarter mile run to date: 13.350@101.79/1.844 60'(7-6-01)Best MPH 101.79(7-6-01) [This message has been edited by Ares (edited 07-18-2001).]

07-19-2001, 10:59 AM	#3
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	Thanks Ares, I'll check it out!