Computer Chip for 99 GT?

dtroman · 12-26-1999, 07:30 PM

I recently purchased a 99 GT (auto) and am thinking about installing a chip (Superchips maybe). Can someone tell me if this really helps. The only mod I currently have is a K&N filter.

------------------

RedGTvert · 12-26-1999, 08:31 PM

Probably not worth it for a N/A Motor. Save you money for other mods . . .

Underdrive pullies, X-pipe with cats to mention 2 that would definately help with hp gains. Will cost a couple hundred more than a chip, but would give you more bang for your buck.

Hammer · 12-26-1999, 09:50 PM

Gears...
First and best bang for your buck...
Personally I recommend 3.73s
Also consider a good aftermarket shifter (Tri-Ax or Pro 5.0 are good choices)

RedGT is correct with the option of underdrive pullies also...

Your money can be put towards better things than a chip on near-stock engine setups.

With your engine putting out 260hp stock and 14 sec quarter miles, a few bucks in the right departments can yield some good times and fun driving.. ;-)

------------------
98 GT
Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

Hammer · 12-26-1999, 09:52 PM

WHOOPS!

I totally missed that your car was an automatic...:-)

Forget about the shifter...

------------------
98 GT
Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

blkhorse · 12-26-1999, 10:01 PM

I am not sure,but isn't the 99 chipless?

RedGTvert · 12-26-1999, 11:13 PM

Hammer, not an AODE person, but I think he will need a chip to correct speedo on AODE for any gears above 3.55's. That is why I didn't recommend.

Blkhrse, yes they are chipless, of cours unless you add a programming chip like a Superchip.

When JMS finally comes out with the Chipmaster, then it might be worth doing but until then on a N/A motor still not worth it.

Hammer · 12-27-1999, 02:52 AM

I'm not an AODE guy either, so I may have mis-spoken...
I don't know if the speedo compensator is a chip per-se, but you called it an Abbott ERA (Electronic Ratio Adaptor).
How this thing would hook in if its not a standard chip upgrade, I don't know.

You out there Red for a little enlightenment?!

------------------
98 GT
Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

[This message has been edited by Hammer (edited 12-28-1999).]

dtroman · 12-27-1999, 11:23 AM

Thanks for the help. I think I will pass on the chip and look into the other mods you guys recommended. By the way, do you have any recommendations on lowering springs. Want to lower the sky rider but don't want to kill my ride. Any of them better than others.

Hammer · 12-27-1999, 12:21 PM

You can't go wrong with a set of Eibach springs!

Also, forgetting about the gears for a moment... Pulleys, an X/H pipe, and a cat-back system will give you a few horses for a bit of cash...

Still waiting on that gear info RedGT!

------------------
98 GT
Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

john edwards · 12-27-1999, 03:07 PM

Having been there done that on my 99 GT aode. I would recomend a Bassani X pipe. Gave me the most performance improvement and exotic sound even with the stock mufflers. Abbott ERA won't work on the AODE cars. Motorsport "C" springs are also recomended. E mail me for where to get these at the best price.

------------------
John Edwards
Mod Motor #2
Yellow 99 GT
13.71 @ 100.69

[This message has been edited by john edwards (edited 12-27-1999).]

EXAM1999 · 12-28-1999, 12:50 AM

With the 99 GT(Auto) toss the converter first. Add a cooler & shift kit and the car will be a rocket off the line. Also add a Bassani X-Pipe and Stainless cat-back and the car should be very fast. Hey John, I received permission from the wife to order the Vortech V2 SQ blower next month when it's released. I'm tired of wasting money on little mods. After the blower, I should hit 12s on street tires.

------------------
EXAM1999
99 Mustang GT
4R70W, Borla Cat-Back, Pro-M77, PI 2800 stall Lock up T/C, cooler & Transgo Shift kit, Synthetics in rear & Type F in trans.
Bassani X-Pipe <--Done
Vortech V2 SQ is next

Hammer · 12-28-1999, 01:10 AM

Thanks for the gear info John...
(This makes sense since RedGTvert uses the Abbot ERA and is not running AODE)

So the question now is (for me), what do the 99-00 AODE GTs use as a speedo compensator?

RedGTvert · 12-28-1999, 04:24 PM

Hammer, guess what, a chip. Superchips is the only compnay I know of right now that can correct speedo's, but i only think up to 3.73's.

Hammer · 12-28-1999, 05:36 PM

Hehe.. figures...;-)
Thanks for the response Red, yer good people.

------------------
98 GT
Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

jameshensler · 12-28-1999, 08:46 PM

Hey guy's one quick ?. On my 5-speed car is there a way to correct the speedo. I have moved from 4.30's to 4.56's and my 21 tooth is a good way off.

------------------
97 cobra, 4.30 gears, mac long tubes, off road h-pipe, dis4, factory five control arms, 31spline axles, locker, 13.00@106 with nitto's

RedGTvert · 12-28-1999, 08:55 PM

Can't help you there, try posting on corral board or hp section of musclestang, they got some good people up there.

12-26-1999, 07:30 PM	#1
dtroman Registered Member Join Date: Dec 1999 Location: Lawrenceville, GA, USA Posts: 2	Computer Chip for 99 GT? I recently purchased a 99 GT (auto) and am thinking about installing a chip (Superchips maybe). Can someone tell me if this really helps. The only mod I currently have is a K&N filter. ------------------

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cobra MAF Conversion kit	toevil1	Windsor Power	7	09-13-2002 02:03 PM
2002 GT vs 1987 GT Review LONG	Unit 5302	Blue Oval Lounge	11	06-09-2002 05:29 PM
Sick 88 Gt Computer problems?	ziggy_2k	Windsor Power	5	06-02-2002 10:33 PM
JMS Chip and 94/95 computer	moponys	Windsor Power	6	09-24-2001 04:33 PM
which computer chip???	acidangel316	Windsor Power	7	06-20-2001 03:03 PM

12-26-1999, 08:31 PM	#2
RedGTvert Registered Member Join Date: Nov 1999 Location: Newtown, PA, USA Posts: 34	Probably not worth it for a N/A Motor. Save you money for other mods . . . Underdrive pullies, X-pipe with cats to mention 2 that would definately help with hp gains. Will cost a couple hundred more than a chip, but would give you more bang for your buck.

12-26-1999, 09:50 PM	#3
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	Gears... First and best bang for your buck... Personally I recommend 3.73s Also consider a good aftermarket shifter (Tri-Ax or Pro 5.0 are good choices) RedGT is correct with the option of underdrive pullies also... Your money can be put towards better things than a chip on near-stock engine setups. With your engine putting out 260hp stock and 14 sec quarter miles, a few bucks in the right departments can yield some good times and fun driving.. ;-) ------------------ 98 GT Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

12-26-1999, 09:52 PM	#4
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	WHOOPS! I totally missed that your car was an automatic...:-) Forget about the shifter... ------------------ 98 GT Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

12-26-1999, 10:01 PM	#5
blkhorse Registered Member Join Date: Jul 1999 Location: Kent Wa Posts: 61	I am not sure,but isn't the 99 chipless?

12-26-1999, 11:13 PM	#6
RedGTvert Registered Member Join Date: Nov 1999 Location: Newtown, PA, USA Posts: 34	Hammer, not an AODE person, but I think he will need a chip to correct speedo on AODE for any gears above 3.55's. That is why I didn't recommend. Blkhrse, yes they are chipless, of cours unless you add a programming chip like a Superchip. When JMS finally comes out with the Chipmaster, then it might be worth doing but until then on a N/A motor still not worth it.

12-27-1999, 02:52 AM	#7
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	I'm not an AODE guy either, so I may have mis-spoken... I don't know if the speedo compensator is a chip per-se, but you called it an Abbott ERA (Electronic Ratio Adaptor). How this thing would hook in if its not a standard chip upgrade, I don't know. You out there Red for a little enlightenment?! ------------------ 98 GT Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit... [This message has been edited by Hammer (edited 12-28-1999).]

12-27-1999, 11:23 AM	#8
dtroman Registered Member Join Date: Dec 1999 Location: Lawrenceville, GA, USA Posts: 2	Thanks for the help. I think I will pass on the chip and look into the other mods you guys recommended. By the way, do you have any recommendations on lowering springs. Want to lower the sky rider but don't want to kill my ride. Any of them better than others.

12-27-1999, 12:21 PM	#9
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	You can't go wrong with a set of Eibach springs! Also, forgetting about the gears for a moment... Pulleys, an X/H pipe, and a cat-back system will give you a few horses for a bit of cash... Still waiting on that gear info RedGT! ------------------ 98 GT Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

12-27-1999, 03:07 PM	#10
john edwards Registered Member Join Date: Sep 1998 Location: Jonesborough, TN USA Posts: 167	Having been there done that on my 99 GT aode. I would recomend a Bassani X pipe. Gave me the most performance improvement and exotic sound even with the stock mufflers. Abbott ERA won't work on the AODE cars. Motorsport "C" springs are also recomended. E mail me for where to get these at the best price. ------------------ John Edwards Mod Motor #2 Yellow 99 GT 13.71 @ 100.69 [This message has been edited by john edwards (edited 12-27-1999).]

12-28-1999, 12:50 AM	#11
EXAM1999 Registered Member Join Date: Mar 1999 Location: Oakdale, NY, US Posts: 50	With the 99 GT(Auto) toss the converter first. Add a cooler & shift kit and the car will be a rocket off the line. Also add a Bassani X-Pipe and Stainless cat-back and the car should be very fast. Hey John, I received permission from the wife to order the Vortech V2 SQ blower next month when it's released. I'm tired of wasting money on little mods. After the blower, I should hit 12s on street tires. ------------------ EXAM1999 99 Mustang GT 4R70W, Borla Cat-Back, Pro-M77, PI 2800 stall Lock up T/C, cooler & Transgo Shift kit, Synthetics in rear & Type F in trans. Bassani X-Pipe <--Done Vortech V2 SQ is next

12-28-1999, 01:10 AM	#12
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	Thanks for the gear info John... (This makes sense since RedGTvert uses the Abbot ERA and is not running AODE) So the question now is (for me), what do the 99-00 AODE GTs use as a speedo compensator?

12-28-1999, 04:24 PM	#13
RedGTvert Registered Member Join Date: Nov 1999 Location: Newtown, PA, USA Posts: 34	Hammer, guess what, a chip. Superchips is the only compnay I know of right now that can correct speedo's, but i only think up to 3.73's.

12-28-1999, 05:36 PM	#14
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	Hehe.. figures...;-) Thanks for the response Red, yer good people. ------------------ 98 GT Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

12-28-1999, 08:46 PM	#15
jameshensler Registered Member Join Date: Jun 1999 Location: lancaster, ohio Posts: 48	Hey guy's one quick ?. On my 5-speed car is there a way to correct the speedo. I have moved from 4.30's to 4.56's and my 21 tooth is a good way off. ------------------ 97 cobra, 4.30 gears, mac long tubes, off road h-pipe, dis4, factory five control arms, 31spline axles, locker, 13.00@106 with nitto's

12-28-1999, 08:55 PM	#16
RedGTvert Registered Member Join Date: Nov 1999 Location: Newtown, PA, USA Posts: 34	Can't help you there, try posting on corral board or hp section of musclestang, they got some good people up there.