![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Aug 2001
Location: Mt. Clemens, MI, USA
Posts: 19
|
![]() Guys,
I need help making a decision here. I have a '96 Saleen S281 with 85,000 miles on it. Tonight, my brother mentioned to me that he knows a guy that wants to get rid of a new '01 4.6 GT engine. My question is the following: If you were me, would you spend roughly $1,500 and do the engine swap? (basically giving me a brand new car that runs stronger and gives the car a longer life span). Last night, my water pump started making noises and I may have a slight oil leak (the LOW OIL light is on). Thanks, Mike
__________________
2002 Black Mustang GT - Cold Fusion Wet Nitrous System (75 shot) - K&N Air Filter - Cold Air Intake - Saleen Springs - Steeda Tri-Ax Shifter - 3.73 gear - BBK Long-tube headers - Dr. Gas Off-road X-pipe - Borla Exhaust - Saleen lower control arms - Saleen underdrive pulleys Best 1/4 (w/o NOS): 13.68 @ 102mph Best 1/4 (w/NOS): 12.93 @ 108mph |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Apr 2001
Location: Sterling Heights,Michigan
Posts: 129
|
![]() Go for it. But it might not be just an engine swap, you might also need the computer from the 01 car also. But i'am not positive.
Will
__________________
SOLD!!! 98Cobra Black on Black Coupe 4.30's DTS diff cover Eaton posi Moser 31 spline axles Spec Stage 2 clutch B&M Ripper shifter BBK off-road x-pipe Steeda pullies Steeda timing adj@14deg MAC cold air Best Time 12.9 @107.5 on street tires New Car 03 Cobra Not Stock |
![]() |
![]() |
![]() |
#3 |
"The Game"
Join Date: Apr 1999
Location: Baytown, Texas USA
Posts: 955
|
![]() You should get that engine as fast as possible. Use your harness, computer, etc. You don't need the '01 computer. Only difference is the coolant sensors. On '96-98 engines there is one sensor on the drivers side (gauge) and one on the passenger side (computer). You will have to relocate the drivers side sensor due to the newer engine's intake having only one sensor location. That is on the passenger side. You can either rig a "T" fitting at that location and plumb both sensors in there or relocate the gauge sensor into the block. There is a coolant plug under the drivers side header towards the front of the block. Install the sensor there, then cut the harness wires, and splice in a section to extend them down to where you can plug in the harness. Quick and easy way to pick up power in the older mod cars.
__________________
SD Wheeler ![]() DTA Racing & Performance THE source for ModMax Components and Modular Power Packages FFW M/M #30-sponsored by Strictly Performance Moderator, Modular Motor & Big Block Forums Hardcore5.0 |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Engine Swap 4Cyl To V8---HELP PLEASE | Coupe Devil | Windsor Power | 6 | 01-29-2008 08:20 PM |
engine swap and more | hunting4bear | Classic Mustangs | 6 | 10-24-2004 06:42 PM |
SC/SC Engine Swap with 6cly Stang? | 1969Mach1 | Small Ponies | 1 | 07-16-2002 05:19 PM |
1967 F-100 Engine Swap | RoadWarrior | Built Ford Tough | 1 | 07-11-2002 05:11 AM |
Engine swap - paint tips? New oil pan? | withamc | Windsor Power | 4 | 05-16-2001 02:15 PM |