Replacing Foglight bulb

grthortoni · 03-30-2002, 11:51 AM

Not the handiest guy in the world, but I figured I could handle replacement of a blown out foglight on a 95 GT......bought the new bulb and haven't been able to figure out the replacement process. Manual is useless because it is a generic Stang book and does not include the foglights. I KNOW someone out there knows how to do this in 30 seconds.......

drudis · 03-30-2002, 12:16 PM

Dont know HOW, but try not to get finger skin oil on bulb, it shortens the lifespan...

joe4speed · 03-30-2002, 01:13 PM

if you follow the wire to the back of the light, you should be able to pull the rubber grommet holding the bulb in. The whole piece comes right out.

Rosco · 03-30-2002, 01:28 PM

Well, I could help ya if it was a 87-93

I can't tell you how many times I've had to change mine. Although it might possibly be the same, where it's connected to the mounting bracket? Oh well. Good Luck

grthortoni · 03-30-2002, 02:38 PM

Hey, figured it out. Soooo much easier to do in the daytime. You need to crawl under the front of the car, reach up behind the front bumper behind the fog light, find the harness and follow it to the lamp. Give the lamp a twist to remove it....and reverse the process to install the new one.

03-30-2002, 11:51 AM	#1
grthortoni Registered Member Join Date: Mar 2002 Location: Deerfield Beach, FL Posts: 2	Replacing Foglight bulb Not the handiest guy in the world, but I figured I could handle replacement of a blown out foglight on a 95 GT......bought the new bulb and haven't been able to figure out the replacement process. Manual is useless because it is a generic Stang book and does not include the foglights. I KNOW someone out there knows how to do this in 30 seconds.......

03-30-2002, 12:16 PM	#2
drudis Moderator Join Date: Dec 1999 Location: Livonia, MI, USA Posts: 1,194	Dont know HOW, but try not to get finger skin oil on bulb, it shortens the lifespan... __________________ Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com

03-30-2002, 01:13 PM	#3
joe4speed He said Member...heh, heh Join Date: Sep 1999 Location: Jupiter, Florida U.S.A. Posts: 3,718	if you follow the wire to the back of the light, you should be able to pull the rubber grommet holding the bulb in. The whole piece comes right out. __________________ *Joe!* 1988 GT, 13.58@101mph Check out my listing! Click here! Or my website:www.joe4speed.com

03-30-2002, 01:28 PM	#4
Rosco Registered Member Join Date: Mar 2002 Location: Vestal, NY Posts: 307	87-93 Well, I could help ya if it was a 87-93 I can't tell you how many times I've had to change mine. Although it might possibly be the same, where it's connected to the mounting bracket? Oh well. Good Luck __________________ 1989 Mustang 5.0 Conversion, Full Saleen ground effects and spoiler, '94 saleen decal set, '93 Saleen Seats, Black interior from a '93, Steeda quadrant, smog pump delete, a/c delete, Steeda Tri-Ax shifter, '97 rear differential, aluminum driveshaft, 5 lug conversion, '97 rear disc brakes, southside upper and lower control arms, '99 GT Anniversary wheels, flowtech longtubes, flowtech offroad H-pipe, saleen lowering springs, kyb shocks, caster/camber plates

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
01 stang headlight bulb replacement	ak_diplomat	Small Ponies	1	08-29-2003 05:01 PM
foglight bulb replacement	82 GT	Windsor Power	4	08-03-2003 05:41 PM
Replacing 96 Mustang Turn Signal Bulb?	icetime97	Modular Madness	0	02-10-2003 01:45 PM
bright light not working? its not the bulb	fiveohpatrol	Windsor Power	3	06-20-2001 02:15 AM
91GT Foglight fix problem!!! HELP PLS!!!	SHaFT7	Windsor Power	1	04-23-2001 10:42 PM

03-30-2002, 02:38 PM	#5
grthortoni Registered Member Join Date: Mar 2002 Location: Deerfield Beach, FL Posts: 2	Hey, figured it out. Soooo much easier to do in the daytime. You need to crawl under the front of the car, reach up behind the front bumper behind the fog light, find the harness and follow it to the lamp. Give the lamp a twist to remove it....and reverse the process to install the new one.