MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Modular Madness
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 05-08-2001, 08:03 AM   #1
Stefan
Registered Member
 
Stefan's Avatar
 
Join Date: Dec 1998
Location: Manhattan, KS 66502
Posts: 599
Thumbs up Gettin' there inch by inch...

I now have my FMS pulleys and my Pro-M 87mm MAF installed and I like what I feel. It's just about what I expected SOTP wise. I have a harder time getting it to bog in first as it has a little more pull right from the get go. My wife and I are saving for a house so this will be it "mod wise" for a while. Next year I'll swap for some 3:73's and a hiflow hpipe. It's a small start but every little bit helps in the long run.
Just thought I'd share.

Brett

------------------
66 Tahoe Turquoise Coupe
Laser Red 96GT Ragtop
30 Years & 30 inches apart in the driveway!

[This message has been edited by Stefan (edited 05-08-2001).]
Stefan is offline   Reply With Quote
Old 05-08-2001, 03:51 PM   #2
T_Bone
Registered Member
 
Join Date: Jul 2000
Location: Minot AFB, ND
Posts: 207
Thumbs up

Congrats on the mods, Stefan! Pulleys are good bang for the buck. The MAF should have waited and 3.73's or H-pipe should've been put in, though. The MAF will increase your throttle response, but you'd be lucky to see any hp out of it without being blown(the car ).

------------------
T-Bones 1997 Cobra#6342 born 6-11-97
Wht/blk, Pro 5.0,FRPP 4.56's, aluminum driveshaft, FRPP throttle body, C&L 80mm MAF, K&N, Steeda U/D pulleys, Steeda timing adjuster, Flowmasters, s/f connectors, FRPP pro springs, BBK caster/cambers.

My old 96GT
T_Bone is offline   Reply With Quote
Old 05-08-2001, 04:01 PM   #3
Stefan
Registered Member
 
Stefan's Avatar
 
Join Date: Dec 1998
Location: Manhattan, KS 66502
Posts: 599
Cool

Yah, I might be working backwards on a few of these mods but I couldn't pass up the deal I got on them. They are the pulleys and MAF off of Hammer's Stang. I got them highly discounted and as I had planned on those two bolt-ons in the future anyway I went ahead and got them. I can't wait to see what gears are gonna feel like as well as getting rid of 4 cats... all in due time.

It's gettin' tough, though, 'cause patients is a shirt I don't wear

------------------
66 Tahoe Turquoise Coupe
Laser Red 96GT Ragtop
30 Years & 30 inches apart in the driveway!
Stefan is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
3 inch piping 01whtegt Modular Madness 3 08-15-2002 12:26 PM
are mac's 3 1/2 inch tail pipes for my setup Chevysucks Windsor Power 1 03-18-2002 03:46 PM
9 inch rear GTSteed89 Windsor Power 1 01-25-2002 01:46 PM
Cubic Inch of the 4.6? 98'MustangGT Modular Madness 7 05-04-2001 11:03 PM
9 inch rear ends Fostang Classic Mustangs 12 02-19-2001 07:23 PM


All times are GMT -5. The time now is 06:49 AM.


SEARCH