Header bolts (HOW)

cbt · 09-26-2000, 04:41 PM

I was going to install my h-pipe today. I started on the passenger side and realized that I can not get the bolt off, It's not that I can't turn it, I just can't get to it. What are you using to get to it. Where can I get it and how much does it cost.

93CobraR · 09-26-2000, 08:41 PM

I installed one on my buddies 98 Gt. You just need the right combination of extentions and swivils.

------------------
87 GT, 4 inch cowl hood, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's.
Best time 13.012
Best MPH 104
Best 60' 1.816
Also a 40' Ford Coupe Legend Race car #16. 1200cc Yamaha, oil cooler, fans.

Visit my site at:
http://www.geocities.com/cobrar93_2000/MyPage.html

cobrayankee · 09-26-2000, 10:05 PM

You just need a 12" extension with a swivel head and I used a metric set. A good light under there will help too. Hit all the bolts with WD-40 or liquid wrench. It just looks like a mess before you get into it. Let us know how it goes.

------------------
1997 Cobra, C+L 80mm MAF, Pro 5.0 shifter, BBK Springs, Taylor Wires, 2 Chamber Flows, ASP Pulleys, MAC off road H pipe.

09-26-2000, 04:41 PM	#1 (permalink)
cbt Registered Member Join Date: Jan 2000 Location: Martin, GA USA Posts: 115	Header bolts (HOW) I was going to install my h-pipe today. I started on the passenger side and realized that I can not get the bolt off, It's not that I can't turn it, I just can't get to it. What are you using to get to it. Where can I get it and how much does it cost.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Where can I find some header bolts?	96_4.6	Modular Madness	5	11-08-2003 10:22 PM
missing header bolts	mak375	Windsor Power	2	04-27-2003 12:05 PM
How do I keep my header bolts in??!?!?	Skyman	Windsor Power	11	07-30-2002 07:01 PM
Stage 8 header bolts?	Rev	Blue Oval Lounge	8	01-13-2002 11:38 PM
header bolts etc	willboske	Windsor Power	5	04-06-2001 07:34 PM

09-26-2000, 08:41 PM	#2 (permalink)
93CobraR Registered Member Join Date: Oct 1999 Location: Cincinnati, Ohio Posts: 1,574	I installed one on my buddies 98 Gt. You just need the right combination of extentions and swivils. ------------------ 87 GT, 4 inch cowl hood, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 13.012 Best MPH 104 Best 60' 1.816 Also a 40' Ford Coupe Legend Race car #16. 1200cc Yamaha, oil cooler, fans. Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html

09-26-2000, 10:05 PM	#3 (permalink)
cobrayankee Registered Member Join Date: Jul 2000 Location: Baltimore, MD Posts: 516	You just need a 12" extension with a swivel head and I used a metric set. A good light under there will help too. Hit all the bolts with WD-40 or liquid wrench. It just looks like a mess before you get into it. Let us know how it goes. ------------------ 1997 Cobra, C+L 80mm MAF, Pro 5.0 shifter, BBK Springs, Taylor Wires, 2 Chamber Flows, ASP Pulleys, MAC off road H pipe.

Sponsored Links