Hooking up Rollstop

Ares · 02-14-2001, 11:47 PM

Has anyone hooked up a rollstop on these new mustangs? I would like to put it in the line coming out of proportioning valve but not sure if ABS pump will let it work or not. So if anyone has some input on thtis would be great.

------------------
2000 GT Laser red-5speed
MAC Cold-air Induction
MAC 2 1/2" cat back exhuast
275/50-15 Drag T/A's used at track
Best Quarter mile run to date: 13.50@99.97 (1.87 60')

blk9946GT · 02-16-2001, 01:35 PM

When I first started to put one on I contacted Sean Hyland. They told me you will have to put one on each front wheel, just wire them to one switch. You cant do it the way you are thinking. I put two on and mine works fine.

Ares · 02-16-2001, 06:59 PM

Ah thanks alot. I kinda had an idea I would have to do it this way, now your reply confirms it. Again thanks.

------------------
2000 GT Laser red-5speed
MAC Cold-air Induction
MAC 2 1/2" cat back exhuast
275/50-15 Drag T/A's used at track
Best Quarter mile run to date: 13.50@99.97 (1.87 60')

white00GT · 02-17-2001, 10:54 PM

When I put the line lock on my 2000 I put it after the ABS and everything works fine. I'm not sure which line it is coming out of the ABS unit, I belive it may be the L1 line but I can go look in the morning. I'm not sure why they would say to use two line locks, but just the one on mine locks both front tires.

Ares · 02-18-2001, 08:09 PM

You have 1 line in ABS for front then 2 lines out. One for left and right front tires. I'd say you have only left front locked. I guess that could work that way.

white00GT · 02-19-2001, 08:02 PM

I was wrong I went, and looked at my car today. My line lock is before the ABS unit. Sorry for the confusion that my have caused.

Ares · 02-19-2001, 08:46 PM

Cool, so what your saying is that linelock wont be affected by ABS pump. OK that means I could put it anywhere between proportioning vavle and ABS

Mustang92 · 02-20-2001, 07:30 AM

Help me out here guys. I've thought about installing one myself but have no experience with brakes (other than changing pads) what all is involved in installing a line lock? With the amount of track abuse my car sees I figure I can help make burnouts a little easier and possibly save wear and tear on the rear breaks. Also the place where your talking about installing the line lock do you have a picture of it or anything?

------------------
00 GT, MAC Offroad H, Steeda Pulleys, Steeda Timing Adjuster, FMS 4.10’s, Flows w/turndowns, UPR shifter, UPR subframes, UPR LCA’s, Air Filter, Lakewood 70/30 & 50/50, Weld Pro Stars, Nitto DR’s, Best ET on DR's 13.09@103.92 (1.81 60ft), Best on ET Drags 12.99@104.60 (1.67 60ft) 244.6 RWHP
M/M 100
88 LX coupe X-FHP, 12pt Cage, UPR K-member, 31 spline rear, full spool…
85 Thunderbird Stock

Ares · 02-20-2001, 05:40 PM

It's not hard really. If you open your hood and stand infront of car look down to your left. Next to where aircleaner would be you will see the ABS pump by the radiator. The Proportioning valve is right under your master cylinder, locate line between the two for front brakes. Each port will be marked to where they lead to or come from. You may need a short piece of brake line to run from out side of linelock to say ABS pump that way you dont cut and splice lines which can blow out after splicing. Then its just a matter of bleeding front brake lines and hooking wires up to a switch somewhere inside car. It will take me longer to run wires then to hook up linelock to brake line. Now I have my project for saterday

[This message has been edited by Ares (edited 02-20-2001).]

Mustang92 · 02-20-2001, 10:42 PM

Sounds simple enough. Is there any one brand linelock that is better than others?

Thanks for the info.

Ares · 02-21-2001, 05:41 PM

Umm I bought a TCI unit from Summit. Hurst also offers a line lock but is a little more money. I'm not to sure who else may make them.

02-14-2001, 11:47 PM	#1
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	Hooking up Rollstop Has anyone hooked up a rollstop on these new mustangs? I would like to put it in the line coming out of proportioning valve but not sure if ABS pump will let it work or not. So if anyone has some input on thtis would be great. ------------------ 2000 GT Laser red-5speed MAC Cold-air Induction MAC 2 1/2" cat back exhuast 275/50-15 Drag T/A's used at track Best Quarter mile run to date: 13.50@99.97 (1.87 60')

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Hooking up elec. fan, What to do about a coolant res.?	MattwantsSpeed	Windsor Power	6	10-23-2002 11:44 AM
hooking up sub to home receiver :D	jj_jonathon	Audio, Security, & Electronics	2	09-08-2002 01:42 PM
hooking up a/f and voltemeter gauges...	MineralGray02K	Modular Madness	0	08-03-2002 11:36 AM
hooking?	89lxinwky	Windsor Power	1	11-17-2001 03:43 AM
Lod noise, bypass and hooking up	Dominick99GT	Special Production	0	12-27-2000 06:00 PM

02-16-2001, 01:35 PM	#2
blk9946GT Registered Member Join Date: Feb 2001 Location: Lorain,OH USA Posts: 2	When I first started to put one on I contacted Sean Hyland. They told me you will have to put one on each front wheel, just wire them to one switch. You cant do it the way you are thinking. I put two on and mine works fine.

02-16-2001, 06:59 PM	#3
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	Ah thanks alot. I kinda had an idea I would have to do it this way, now your reply confirms it. Again thanks. ------------------ 2000 GT Laser red-5speed MAC Cold-air Induction MAC 2 1/2" cat back exhuast 275/50-15 Drag T/A's used at track Best Quarter mile run to date: 13.50@99.97 (1.87 60')

02-17-2001, 10:54 PM	#4
white00GT Registered Member Join Date: Nov 2000 Location: Pawleys Island SC Posts: 229	When I put the line lock on my 2000 I put it after the ABS and everything works fine. I'm not sure which line it is coming out of the ABS unit, I belive it may be the L1 line but I can go look in the morning. I'm not sure why they would say to use two line locks, but just the one on mine locks both front tires.

02-18-2001, 08:09 PM	#5
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	You have 1 line in ABS for front then 2 lines out. One for left and right front tires. I'd say you have only left front locked. I guess that could work that way.

02-19-2001, 08:02 PM	#6
white00GT Registered Member Join Date: Nov 2000 Location: Pawleys Island SC Posts: 229	I was wrong I went, and looked at my car today. My line lock is before the ABS unit. Sorry for the confusion that my have caused.

02-19-2001, 08:46 PM	#7
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	Cool, so what your saying is that linelock wont be affected by ABS pump. OK that means I could put it anywhere between proportioning vavle and ABS

02-20-2001, 07:30 AM	#8
Mustang92 Drag Racer! Join Date: Nov 1999 Location: Lake Worth, FL USA Posts: 757	Help me out here guys. I've thought about installing one myself but have no experience with brakes (other than changing pads) what all is involved in installing a line lock? With the amount of track abuse my car sees I figure I can help make burnouts a little easier and possibly save wear and tear on the rear breaks. Also the place where your talking about installing the line lock do you have a picture of it or anything? ------------------ 00 GT, MAC Offroad H, Steeda Pulleys, Steeda Timing Adjuster, FMS 4.10’s, Flows w/turndowns, UPR shifter, UPR subframes, UPR LCA’s, Air Filter, Lakewood 70/30 & 50/50, Weld Pro Stars, Nitto DR’s, Best ET on DR's 13.09@103.92 (1.81 60ft), Best on ET Drags 12.99@104.60 (1.67 60ft) 244.6 RWHP M/M 100 88 LX coupe X-FHP, 12pt Cage, UPR K-member, 31 spline rear, full spool… 85 Thunderbird Stock

02-20-2001, 05:40 PM	#9
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	It's not hard really. If you open your hood and stand infront of car look down to your left. Next to where aircleaner would be you will see the ABS pump by the radiator. The Proportioning valve is right under your master cylinder, locate line between the two for front brakes. Each port will be marked to where they lead to or come from. You may need a short piece of brake line to run from out side of linelock to say ABS pump that way you dont cut and splice lines which can blow out after splicing. Then its just a matter of bleeding front brake lines and hooking wires up to a switch somewhere inside car. It will take me longer to run wires then to hook up linelock to brake line. Now I have my project for saterday [This message has been edited by Ares (edited 02-20-2001).]

02-20-2001, 10:42 PM	#10
Mustang92 Drag Racer! Join Date: Nov 1999 Location: Lake Worth, FL USA Posts: 757	Sounds simple enough. Is there any one brand linelock that is better than others? Thanks for the info.

02-21-2001, 05:41 PM	#11
Ares Registered Member Join Date: Oct 2000 Location: Saxonburg, PA, USA Posts: 236	Umm I bought a TCI unit from Summit. Hurst also offers a line lock but is a little more money. I'm not to sure who else may make them.