New Blower but can't Hammer! uggghhh
 

Well, just picked up the 96 GT with the new Huffer on it. It's pingin' pretty bad so now I gotta go to 30lb injectors, bigger MAS air and recal. the FMU. You know how you look forward to something FOREVER only to find out you STILL have to WAIT SOME MORE. AAAARRRRRGGGGHHH!!!! Just venting - anybody else go through this?

------------------
96GT, Vortech S-Trim, 3.73, Bassani X, Flows, 70mm TB, Subs, Mega-Bite Jr.Lower rear Ctrl Arms, FMS Uppers, Ripper, and a bunch of other $tuff I can't seem to remember!

yea, nothing like a bolt on blower...oh, and by the way, don't forget to get a bigger in-tank pump, an in-line pump, bigger injectors, new mass air calibration and a custom chip will help with all the new surging problems because there's so much few now at cold start...but it's a straight bolt on! you gotta love it!

------------------
cool tan
5.0 cover car may 99
triple threat

Hey C.T. - Yeah, fortunately I've done all the other stuff (ok., except for a DIS-4 ignition to retard the timing!) MOD MOTORS - YA GOTTA LOVE 'EM!

------------------
96GT, Vortech S-Trim, 3.73, Bassani X, Flows, 70mm TB, Subs, Mega-Bite Jr.Lower rear Ctrl Arms, FMS Uppers, Ripper, and a bunch of other $tuff I can't seem to remember!

glad to hear your got your blower! have some questions though, i was under the impresion that vortech set-up was ready to go as shipped. did they screw you around? now that you went with them what would have been a better choice if your stang could double as a time machine? hope it works out for the best!!!
97 gt NOS

Thx for the congrats shifty - Actually, it would appear that the blower is TOO good - it's rated @ 6-9 psi but we got 12 on the gauge! With that much boost it's no wonder - What really sucks is that Pro-M is closed for the holidays and I'm gonna have to wait until Y2K to be cruzin' my blown Stang! (30lb injectors already ordered!)

Mod motor cars are drivers, no hot rods unless you are rich.
89-93 W/powerdyne=cheep fun

Cheap fun until that Powerdyne chews itself to pieces, and spits metal shavings into your engine!

Several of my friends found this out the hard way...

------------------
1989 Mustang GT, Charcoal Gray w/Titanium, 71k miles
13.413@108.95 -- 2.159 60ft. on SZ50's
FMS 3.55 gears, Tremec 3550 w/Hurst Comp. Plus shifter, Steeda alum. quadrant, FMS HD clutch kit, Compucar N2O, 16" x 8.5" O.Z. Italy Monte Carlo wheels with 245/50ZR16 Firestone SZ50 tires, BBK 1 5/8" Jet-Hot long tubes, Dr. Gas X-pipe, Dynomax CVX cat-back, Factory Five upper and lower rear control arms, SVO pulleys, Accel 300+ ignition and plug wires, K&N conical filter, 75mm Pro-M, '93 Cobra rear valance, Auto Meter gauges, '93 Cobra intake, FMS 65mm TB, Kirban adj. fuel pressure regulator @ 42psi.
Chad's Virtual House

glad you spoke up about powerdyne, i'm running 125 nos setup with in line booster pump designed for mod motor and was getting stupid ideas about a small blower in conjunction with a more moderate shot of nitrous! any thoughts?

Here is my thought, if you are going with any blower at all...

Vortech S-trim!

------------------
1989 Mustang GT, Charcoal Gray w/Titanium, 71k miles
13.413@108.95 -- 2.159 60ft. on SZ50's
FMS 3.55 gears, Tremec 3550 w/Hurst Comp. Plus shifter, Steeda alum. quadrant, FMS HD clutch kit, Compucar N2O, 16" x 8.5" O.Z. Italy Monte Carlo wheels with 245/50ZR16 Firestone SZ50 tires, BBK 1 5/8" Jet-Hot long tubes, Dr. Gas X-pipe, Dynomax CVX cat-back, Factory Five upper and lower rear control arms, SVO pulleys, Accel 300+ ignition and plug wires, K&N conical filter, 75mm Pro-M, '93 Cobra rear valance, Auto Meter gauges, '93 Cobra intake, FMS 65mm TB, Kirban adj. fuel pressure regulator @ 42psi.
Chad's Virtual House

I have a Vortech S-trim installed it myself. Had no problems at all with it. Any questions mail me at 281cammer@altavista.net
Killercammer

------------------
98 GT
Vortech S-trim
80mm Pro-M
75mm BBk Throttle body
3.55 FMS gears
Flowmaster Catback
Steeda Tri-ax shifter
Jamex 1.5 springs
Power Slot rotors
17x9 Chrome Cobra R's