MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 12-13-2002, 01:46 AM   #1
1991GT
Registered Member
 
1991GT's Avatar
 
Join Date: Jul 2002
Location: Flemington, NJ
Posts: 13
Unhappy Help!! Exhaust Leak

After 2 weeks, a returned set of headers and tailpipes that didnt fit, I finally got my exhaust on my car (BBK 1 5/8 ceramic unequal shorties, BBK h-pipe w/ cats, and flowmaster 2 chambers). Well its sounds sick as hell BUT I have a wonderful exhaust leak that I don't know what to do about. I'm almost positive its coming from the right side header where it bolts up to the h-pipe. the alignment didnt look too swift when I was installing it but i thought the flange would straighten itself out as I tightened it. Also the car feels much slower and feels like I lost power all throughout the rpm range, which I could understand some torque loss because everything is bigger diameter than stock, but not like this. Maybe the leak is causing the power loss?? Also sounds like its misfiring too but I think that may just be the leak that I'm hearing. I did trim the header flange with a carbide cutter to 2 1/2in diameter because it came from the factory at only 2 1/4in and I wanted everything to match. I put black silicone around the flange to try and make it seal better in case I got a leak like this. I also disconnected the battery for a day or so to clear the computer. I only drove it for 8 miles so maybe the computer hasn't re-learned everything yet. I really don't know what else to do...tomorrow I'm going to try and unbolt the header flange and re-align it and hopefully that will fix the problem. Please give me some ideas, I'm desperate!! The leak just makes an otherwise beautiful sounding exhaust sound like crap and the car doesnt feel fast anymore. Help!!
__________________
'91 GT - 135K miles
T-5, stock 2.73's uugh, MAC cold air, Pro-M Bullet 75mm, BBK 1 5/8 jet-hot unequal shorties, BBK h-pipe w/ cats, Flowmaster 2 chambers, Pro 5.0 short throw, KYB shocks and struts

In the garage waiting to be put on:
Screamin Demon coil, Dyna Mod TFI module, underdrive pulleys
1991GT is offline   Reply With Quote
Old 12-13-2002, 01:57 AM   #2
Bad89stang
Registered Member
 
Bad89stang's Avatar
 
Join Date: Aug 2001
Location: Ft. Worth, TX
Posts: 456
Default Get back under there...

Just re-do the connections to the H-pipe. Undo both of them and make sure that they line up correctly. Then tighten them down a little at a time. Switch sides back and forth until you are sure they are tight. For insurance you can add 3-4 washers on each side to get them to tighten earlier. I have screwed with this problem on a friend's car more than I would like to admit.
__________________
You're gonna need your seatbelt
Bad89stang is offline   Reply With Quote
Old 12-13-2002, 11:37 AM   #3
1991GT
Registered Member
 
1991GT's Avatar
 
Join Date: Jul 2002
Location: Flemington, NJ
Posts: 13
Default

I went outside this morning and tried tightening up the flange more. Didn't help. I didn't have the time to unbolt both and re-align them (I did this whole project on my back using jackstands, wish I knew someone that had a lift ) I also checked the plug wires to make sure they were fully seated incase I was hearing a misfire. Two other things I noticed, 1) The exhaust does smell rather rich but maybe its due to the new O2 sensors and exhaust and 2) It did not start leaking until it warmed up. Tonight I will try unbolting and re-aligning the h-pipe/header flanges. Hope that fixes it otherwise I'm going to have to take it somewhere and spend $ that I don't have
__________________
'91 GT - 135K miles
T-5, stock 2.73's uugh, MAC cold air, Pro-M Bullet 75mm, BBK 1 5/8 jet-hot unequal shorties, BBK h-pipe w/ cats, Flowmaster 2 chambers, Pro 5.0 short throw, KYB shocks and struts

In the garage waiting to be put on:
Screamin Demon coil, Dyna Mod TFI module, underdrive pulleys
1991GT is offline   Reply With Quote
Old 12-13-2002, 12:44 PM   #4
bigred90gt
2 Stangs in the Stable
 
bigred90gt's Avatar
 
Join Date: Apr 2002
Location: Baytown, TX
Posts: 1,209
Default

I had the same problem with my Bassani o/r X pipe. I had to cut the pipe, on the side that had the leak, bolt the piece to the header, and then weld a sleeve to cover the gap. Looks bad but works. I don't know if you will have room to do so with the cats, but It's worth a look.
Caymon
__________________
'90 GT Under construction
Best E.T. = Fast @ High Speeds - OK So I Lie. So What!!!
04 F-150 STX 4.2L 5 spd
Rice Haters Club Member #128
bigred90gt is offline   Reply With Quote
Old 12-13-2002, 01:23 PM   #5
RED92LX50
Registered Member
 
RED92LX50's Avatar
 
Join Date: Aug 1999
Location: Fairfax, VA
Posts: 220
Default maybe...

If you are sure the leak is at the header/h-pipe junction, you may be able to put a bead of muffler mender around the joint to stop the leak. It is smilar to using plumbers putty on leaky pipe joints. I used it on one of my connections and have not had any problems in over 6 years.

Otherwise, maybe the leak is at the heads - in which case you can retorque those bolts (as they can loosen a little after the inital install with the first few heat cycles).
__________________
1992 LX 5.0 Convertible Red/Blk
Gears, Exhaust, bolt-ons...
R.H.C. #51
RED92LX50 is offline   Reply With Quote
Old 12-13-2002, 09:39 PM   #6
1991GT
Registered Member
 
1991GT's Avatar
 
Join Date: Jul 2002
Location: Flemington, NJ
Posts: 13
Default

Thanks for all the help. I can't work on it tonight because it's raining but I should be able to work on it over the weekend. I'll keep you guys posted.
__________________
'91 GT - 135K miles
T-5, stock 2.73's uugh, MAC cold air, Pro-M Bullet 75mm, BBK 1 5/8 jet-hot unequal shorties, BBK h-pipe w/ cats, Flowmaster 2 chambers, Pro 5.0 short throw, KYB shocks and struts

In the garage waiting to be put on:
Screamin Demon coil, Dyna Mod TFI module, underdrive pulleys
1991GT is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Exhaust leak StateTroopCoupe Windsor Power 1 09-25-2003 08:21 AM
Speed Secret # 4 jim_howard_pdx Windsor Power 13 11-10-2002 03:42 PM
Header gaskets Stang951 Windsor Power 18 11-01-2002 05:57 PM
finding an exhaust leak TOM90LX Windsor Power 3 01-23-2002 11:15 AM
Exhaust leak? oamunoz Classic Mustangs 4 07-13-2001 03:00 AM


All times are GMT -5. The time now is 10:45 PM.


SEARCH