Our new all modular forum

StangFlyer · 11-13-1999, 06:58 PM

It was requested, and we agreed, the site was past due for a forum dedicated to the Modular 4.6l Mustangs!

Enjoy!

------------------
Dan McClain, Editor
The Mustang Works Online
1991 Mustang GT - 10.90 @ 122 Mph
Built, Blown, and Fast as Hell!

blkhorse · 11-13-1999, 08:08 PM

allright!!! great job!!!!

Dino · 11-13-1999, 08:23 PM

Thanks for the new forum Dan. I don't own a modular mustang yet but Monday I'm going to the dealer to see about getting a 96 GT that they have there. So I'm sure this forum will come in handy when and if I get the new one.

jameshensler · 11-14-1999, 08:15 PM

Hat's off! This I'm sure is going to be a good forum because not alot of 5.0 guy's know anything about 4.6's. Long overdue!

Danbo · 11-14-1999, 10:20 PM

Dan,
Good job.
I like the old 5.0L motor, but
that's not what I drive. Some "go fast"
advice crosses over, but most dosen't.
Besides...It's been over 3 years since there's been a Mustang produced with a
302cid motor; you do the math.

Dan

------------------
'96 Cobra, Steeda G-Trac
Stage III Suspension, K&N
Filter,77mmPro-M,FMS Ceramic
Coated Headers,Bassini-X Pipe,
FMS Aluminum driveshaft,
FMS 3.73's, Cobra R's ,
Firestone SZ-50 275-40x17's,
Powerslot Rotors, Preformance Friction Z rated pads,
Steeda Tir-Ax, Schroth Restraints,
Kuhmo Victoracers(for the track).

Kev98gt · 11-15-1999, 08:21 AM

Thank you!!!!!!!

lewillie · 11-15-1999, 08:49 AM

Amen. 99 GT 4.6
P.S. Contrary to most opinion from earlier 4.6ers, the 99 does respond well to M.S. headers. Well worth the effort.
Tks lewillie

------------------
99/ Silver GT 4.6 SOHC
M.S. headers 3.27

Rebel79 · 11-15-1999, 01:35 PM

Good thinking Dan. Way to go! You just took this board to the next level!

kg2hk · 11-16-1999, 09:30 AM

Thanks for the forum... I felt the 4.6's were getting lost out there...

11-13-1999, 06:58 PM	#1
StangFlyer Founder Join Date: Jun 1995 Location: Michigan Posts: 19,326	Our new all modular forum It was requested, and we agreed, the site was past due for a forum dedicated to the Modular 4.6l Mustangs! Enjoy! ------------------ Dan McClain, Editor The Mustang Works Online 1991 Mustang GT - 10.90 @ 122 Mph Built, Blown, and Fast as Hell!

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Modular Madness Forum FAQ (Read This First!)	Hammer	Modular Madness	0	07-13-2002 01:18 AM
Paxton/Steeda Modular Shootout steps up into high gear	Dave King	Modular Madness	1	05-14-2000 07:34 PM
Modular Shootout car show incentives	Dave King	Modular Madness	0	04-16-2000 05:22 PM
Modular Shootout update	Dave King	Modular Madness	0	03-19-2000 04:06 PM

11-13-1999, 08:08 PM	#2
blkhorse Registered Member Join Date: Jul 1999 Location: Kent Wa Posts: 61	allright!!! great job!!!!

11-13-1999, 08:23 PM	#3
Dino Registered Member Join Date: Nov 1998 Location: Fredericton, New Brunswick, Canada Posts: 74	Thanks for the new forum Dan. I don't own a modular mustang yet but Monday I'm going to the dealer to see about getting a 96 GT that they have there. So I'm sure this forum will come in handy when and if I get the new one.

11-14-1999, 08:15 PM	#4
jameshensler Registered Member Join Date: Jun 1999 Location: lancaster, ohio Posts: 48	Hat's off! This I'm sure is going to be a good forum because not alot of 5.0 guy's know anything about 4.6's. Long overdue!

11-14-1999, 10:20 PM	#5
Danbo Registered Member Join Date: Jul 1999 Location: baltimore Posts: 99	Dan, Good job. I like the old 5.0L motor, but that's not what I drive. Some "go fast" advice crosses over, but most dosen't. Besides...It's been over 3 years since there's been a Mustang produced with a 302cid motor; you do the math. Dan ------------------ '96 Cobra, Steeda G-Trac Stage III Suspension, K&N Filter,77mmPro-M,FMS Ceramic Coated Headers,Bassini-X Pipe, FMS Aluminum driveshaft, FMS 3.73's, Cobra R's , Firestone SZ-50 275-40x17's, Powerslot Rotors, Preformance Friction Z rated pads, Steeda Tir-Ax, Schroth Restraints, Kuhmo Victoracers(for the track).

11-15-1999, 08:21 AM	#6
Kev98gt Registered Member Join Date: Nov 1998 Location: Rockville, Maryland Posts: 49	Thank you!!!!!!!

11-15-1999, 08:49 AM	#7
lewillie Registered Member Join Date: Oct 1999 Location: Ste, Catherine, quebec, Canada Posts: 23	Amen. 99 GT 4.6 P.S. Contrary to most opinion from earlier 4.6ers, the 99 does respond well to M.S. headers. Well worth the effort. Tks lewillie ------------------ 99/ Silver GT 4.6 SOHC M.S. headers 3.27

11-15-1999, 01:35 PM	#8
Rebel79 News Editor Join Date: Apr 1999 Location: Concord, CA Posts: 2,101	Good thinking Dan. Way to go! You just took this board to the next level!

11-16-1999, 09:30 AM	#9
kg2hk Registered Member Join Date: Oct 1999 Location: Stony Point. NY Posts: 18	Thanks for the forum... I felt the 4.6's were getting lost out there...