crane cam dyno results are in ,kind of?

46stang · 12-02-2001, 02:12 AM

I went to get my car dyno tuned today but didn't get any tuning

something came up and he couldn't burn me a chip

they gave me 3 pulls so he could get a baseline and have a program ready to try when i go back in two weeks. I made 285rwhp and 303rwtq. so I'm hoping i can hit the magic 300rwhp with a chip? the only mod I've done is the crane cams since my last dyno time. here is a direct comparison of stock 99 cams and my crane cams. I did have a little tuning done to get the 271rwhp(via timing adj and fuel psi reg) but the 285rwhp we didn't touch a thing. fyi.
Leon

Mercury · 12-02-2001, 03:03 AM

Did you post prior to this about Crane Cams for a Mod motor? I thought I saw a prior post.

Anyway, I checked the Crane site and couldnt find any cams for the Mod motors. Are yours a Custom grind? If not, can you steer me in the right direction. How much did they cost ya? I'm considering camming my 2000 GT, if I find a good price of course.

SMOKE · 12-02-2001, 06:38 AM

Good looking NA 4.6er,

46stang · 12-02-2001, 11:39 AM

i don't think i posted earlier. crane doesn't advertise 4.6 cams

. you basically send them your cams and they regrind them and send them back. I had an extra set of cams so i sent them in and then swapped the cams when they came back. it takes roughly 3 weeks mailing it on the ground. they are the cheapest I've found. it cost $305 for everyhthing. call the tech line and ask for dave maxwell he has the hook up for the mod motors. you may also want to consider a chip with the cams as my car does stall once in awhile at a stop light. fyi.

::Good looking NA 4.6er:: Thanks

Leon

Skyman · 12-04-2001, 01:11 PM

Your getting some awesome numbers there. Where did you go for the dyno this time? I really want to get back to the dyno and the track as soon as I can. My car is finally all up and running now so I am ready to go whenever.

285rwhp w/ out tuning is awesome!

Skyler

46stang · 12-04-2001, 08:58 PM

Thanks Sky! i went to morgan motorsports in the valley off of reseda.(dyno jet dyno

unlike germansons

)

http://www.mmsracing.com/

have you changed your email sky? i emailed you a couple times but never got a response?? i figured i probably screwed up some how!

I want to get a chip programmed in a few weeks then I'm definately down for a carlsbad run!! maybe with your slicks a 12.9x et??????
Leon

12-02-2001, 03:03 AM	#2
Mercury The Redneck James Bond Join Date: Sep 2000 Location: Fayetteville NC Posts: 1,707	Did you post prior to this about Crane Cams for a Mod motor? I thought I saw a prior post. Anyway, I checked the Crane site and couldnt find any cams for the Mod motors. Are yours a Custom grind? If not, can you steer me in the right direction. How much did they cost ya? I'm considering camming my 2000 GT, if I find a good price of course. __________________ 64 1/2 "D" code Red Mustang Coupe. Red Baron, 2000 Perf Red Mustang GT. 5spd. Stage 2 CNC heads with Large Valves, Comp Cams (270-274 dur .550 lift), Forged Crank, DRP pistons, Manly H-beams, Pro M 87 mm Mass Air, 24lb Inj, 75mm TB, Plenum Spacer ,Long Tube Headers, Homemade H-pipe, 2 chamber Flows, 4:10's, Steeda Tri-Ax, LKW 70/30's, Eibach Drag Springs, Steeda SubFrames, Battle Boxes, Rear Girdle, Adj uppers, Alunimum Drshft, Southside Lift Bars. Project Cars, 64 1/2 6cyl coupe, 1930 Model A Nostalgia Rod.

12-02-2001, 11:39 AM	#4
46stang Registered Member Join Date: May 1999 Location: moorpark ca Posts: 340	i don't think i posted earlier. crane doesn't advertise 4.6 cams. you basically send them your cams and they regrind them and send them back. I had an extra set of cams so i sent them in and then swapped the cams when they came back. it takes roughly 3 weeks mailing it on the ground. they are the cheapest I've found. it cost $305 for everyhthing. call the tech line and ask for dave maxwell he has the hook up for the mod motors. you may also want to consider a chip with the cams as my car does stall once in awhile at a stop light. fyi. ::Good looking NA 4.6er:: Thanks Leon __________________ 03 sonic blue cobra coupe, 11.49@122mph bakerfield raceway! 11.67@120mph fontana 98 GT, stock for now.

12-04-2001, 01:11 PM	#5
Skyman I need 110mph Trap Speed! Join Date: Feb 1999 Location: So, CA Posts: 4,315	Your getting some awesome numbers there. Where did you go for the dyno this time? I really want to get back to the dyno and the track as soon as I can. My car is finally all up and running now so I am ready to go whenever. 285rwhp w/ out tuning is awesome! Skyler __________________ 2001 BMW M3 6spd 12.79@108 RIP ---- 1993 Notch w/ 98 4V 4.6 Fasttt... -1989 Saleen Mustang #406- 12.32@109 -1999 Black Cobra Coupe- JBA Shorties, Bassani Cat-X, Magnaflow 3", Pulleys, 85mm Pro-M, Ported Intake, Soild Rear w/ 4.30s, Tubular Front End, X2C arms, 13lb batt, few others.

12-04-2001, 08:58 PM	#6
46stang Registered Member Join Date: May 1999 Location: moorpark ca Posts: 340	Thanks Sky! i went to morgan motorsports in the valley off of reseda.(dyno jet dyno unlike germansons ) http://www.mmsracing.com/ have you changed your email sky? i emailed you a couple times but never got a response?? i figured i probably screwed up some how! I want to get a chip programmed in a few weeks then I'm definately down for a carlsbad run!! maybe with your slicks a 12.9x et?????? Leon __________________ 03 sonic blue cobra coupe, 11.49@122mph bakerfield raceway! 11.67@120mph fontana 98 GT, stock for now.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
331 Dyno results	302 LX Eric	Windsor Power	12	04-29-2004 10:13 PM
you will NOT believe this... dyno results	fiveohpatrol	Windsor Power	27	11-27-2001 02:53 PM
DYNO results, and questions	mmike	Windsor Power	7	09-24-2001 09:11 PM
Dyno results inside with timing adjuster installed	Mustang92	Modular Madness	7	02-20-2001 09:24 PM

12-02-2001, 06:38 AM	#3
SMOKE Old School ROUSH Join Date: Nov 1999 Location: Stockbridge, GA Posts: 531	Good looking NA 4.6er,