![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Feb 2002
Posts: 6
|
![]() ![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#2 |
AKA "Dr. Evil"
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
|
![]() The T45 and the rear end are not weak, they just weren't designed for applications with high-torque numbers...
My stock T45 lasted about a year with about 450 hp at the crank. I'm currently looking at a Tremec TKO for replacement. The stock rear end could use some work right about now too, so I expect to do some work back there also in the spring. (Bearings, Shims and seals) As far as blowers, the amount of boost you can run on a near stock setup is usually determined by what type of blower you are looking for. With a roots type, I would stay around 6 psi. A centrifugal blower, about 8 psi. I would advise some engine work before going any higher than that. As in any blown application, watch your compression ratio and be safe out there... ![]()
__________________
Uncle Sam "What the hell is up with all the gauges? Calling Captain Kirk, your ride awaits... Phasers on stun...." |
![]() |
![]() |
![]() |
#3 |
Git jiggy
Join Date: Oct 1999
Location: MO USA
Posts: 865
|
![]() One big thing that'll help your tranny is an aftermarket shifter. The rear end, like Adam said, is a good one. The 8.8 is actually pretty strong. When you go to really sticky tires like slicks is when it starts to take a toll on the rear end.
The roots blower will give you more torque right off the bat because it doesn't have to spool up like the centrifugal. But the centrifugal has the advantage on the upper end of the hp range in the higher rpms. Both will help greatly with hp and torque. Just depends on your combination/application of mods and use of the car as to whether you need the power a little sooner or a little later. Just look at Adam's stang running 450hp with the centrifugal.
__________________
1967 Mustang Coupe |
![]() |
![]() |
![]() |
#4 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
![]() As far as the stock bottom end of the 4.6 goes, 400-450hp is about the limit from what I hear.
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Feb 2002
Posts: 6
|
![]() O.K. thanks for the info. But one more question. If I buy a roots style blower you say to run about 6psi...how come the centrifugal can run at 8psi ? Is it because the roots makes so much more low RPM torque or is there some other reason , and will the aftermarket pulleys effect the performance of the blower ?
![]() |
![]() |
![]() |
![]() |
#6 |
AKA "Dr. Evil"
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
|
![]() The recommended PSI differences are just in the nature of the beasts. One of the reasons is certainly the high torque output at low rpms of the roots style.... along with other issues that others may be able to explain better than I....
Remember that output doesn't necessarily directly respond to boost numbers. Case in point: An intercooled setup can produce more horspower at 8 psi than a non-intercooled unit at 10 psi. As fas as pullies go... Almost every blower setup I know of either comes with their own set or expects you to use the stock pieces.
__________________
Uncle Sam "What the hell is up with all the gauges? Calling Captain Kirk, your ride awaits... Phasers on stun...." |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Finally dyno tests for the C&L plenum for 96-98 Gt's WITHOUT PI heads, link posted | 96_4.6 | Modular Madness | 5 | 11-01-2003 12:43 PM |
oil pan vs. drag link | ScottA40422 | Classic Mustangs | 0 | 08-08-2003 03:20 PM |
Fusible Link | Brian Browning | Classic Mustangs | 0 | 02-16-2001 02:12 PM |
Someone, link a TX streetracing site | 90dpscoupe | Stang Stories | 2 | 01-23-2001 01:49 PM |