porting your mustang!

gt96 · 04-30-2003, 07:18 PM

hey mustang enthusiasts! i have a 96 gt and i was just wondering what kind of port work you can do for my car? as you now it is a plastic intake so you can not port your intake or polish? so if anyone has feedback i would appreciate it!

Badass_yellowGT · 04-30-2003, 08:24 PM

they just did a article in muscle mustang on port matching the throttle body and plenum on the 4.6 and gained 10 hp and 14 tq not bad for i think it said 149.99

96_4.6 · 05-01-2003, 11:26 PM

Sweet, i have a 96 gt!!! I will have to look into this, dont know of many places here in michigan

gt96 · 05-02-2003, 01:20 AM

is the plenum the box ontop of the intake manifold that your tb bolts up to? if i ported the plenum and tb my self could i cause my car any damage? if done wrong? if so what could occur?

biecomp · 05-02-2003, 07:02 PM

I got a used on on e-bay to port it. You don't have to worry about messing up the one on the car and you can take your time with it. Check e-bay or your local junk yards for one and port that. Than do the swap. If everything works well , port the one you took off the car and sell it.

Badass_yellowGT · 05-03-2003, 09:45 AM

yes it is the part the tb attaches to the only problem i could see is if you port it to much like said buy a used one and do it on that.thats what i`m doing

surfbeast · 05-04-2003, 06:52 PM

I purchased a used T/B and plenum on E-Bay also and polished the plenum and T/B to a mirror finish. I also noticed that the inside of the plenum was really rough and had lots of slag hanging in it. I ported it as much as the tools I had allowed and polished it out. I put an intake spacer in ( $ 15, what the hell.. if it helps it helps) and hopefully the port job helped out. With all the rough edges and drag caused in the thing it had to help. Best of all it was free except for the cost of the dremel bits and my time. I polished my old plenum and sold it for $75 bucks! only pais $25 for the used one with the T/B!

TigerBravo · 05-08-2003, 10:19 PM

I read the same article in mm&ff and they specifically said that it was a mod you could do on the 99 & ^ gt. I was wondering if the same could be done on any 4.6 (96 & ^). I am going to be adding a sc to my 98 and that would definately be a plus to my set up.

blue00gt · 05-09-2003, 10:51 AM

I think that on pre-'99(?) cars the walls of the plenum are not as thick and don't allow you to remove enough material compared to the newer plenums, but you can put a ported '99+ plenum on your '96-'98.
If you call Ben Alameda Racing there is a message saying that they don't take cores anymore because of all the 'unusable' cores they received. Because of this it now costs you $220 to buy one from them.

TigerBravo · 05-09-2003, 05:20 PM

Quote:

Originally posted by blue00gt
I think that on pre-'99(?) cars the walls of the plenum are not as thick and don't allow you to remove enough material compared to the newer plenums, but you can put a ported '99+ plenum on your '96-'98.
If you call Ben Alameda Racing there is a message saying that they don't take cores anymore because of all the 'unusable' cores they received. Because of this it now costs you $220 to buy one from them.

Cool, thanks!

ajcolv · 05-12-2003, 03:39 PM

Does the 99+ upper fit the 96-98's without any issues? Is it basically a straight swap?

surfbeast · 05-12-2003, 06:01 PM

Yes it fits. Tha one I purchased was from a 2001. I ported it myself. Cost about $10 bucks. Also ported my old 98 plenum. I may not have done as good a job as the pros but mine was probably as good. It had to help, you would not believe what the inside of the plenum looks like

. I figured it would be all smooth and clean, "NOT!". even if you clean it up a little it would have to help!

04-30-2003, 07:18 PM	#1
gt96 Registered Member Join Date: Apr 2003 Location: utah Posts: 39	porting your mustang! hey mustang enthusiasts! i have a 96 gt and i was just wondering what kind of port work you can do for my car? as you now it is a plastic intake so you can not port your intake or polish? so if anyone has feedback i would appreciate it! __________________ sky 96 mustang gt:ram air, k&n, intake spacer, o\r x, flowmasters, pulleys, nitto drag radials, plugs, wires, 180 stat,

04-30-2003, 08:24 PM	#2
Badass_yellowGT Registered Member Join Date: Jun 2002 Location: Western,MA Posts: 254	they just did a article in muscle mustang on port matching the throttle body and plenum on the 4.6 and gained 10 hp and 14 tq not bad for i think it said 149.99 __________________ Rice Haters Club Member #55 For My car Specs Click the Home page link http://www.badassyellowgt.50g.com/

05-01-2003, 11:26 PM	#3
96_4.6 Registered Member Join Date: Jul 2002 Location: Michigan Posts: 417	Sweet, i have a 96 gt!!! I will have to look into this, dont know of many places here in michigan __________________ 1996 Mustang GT, AODE -Trickflow Upper Plenum -BBK 70mm Throttlebody -02 PI Lower Intake -March Pulleys -BBK H-Pipe -2 Chamber Flowmaster mufflers -3000 RPM Stall -JLT CAI with special K&N -MSD Supercondutor wires -180 stat -FRPP 4:10's *FOR SALE C&L TRUE FLOW INLET PIPE WITH K&N* My Stang

05-02-2003, 01:20 AM	#4
gt96 Registered Member Join Date: Apr 2003 Location: utah Posts: 39	is the plenum the box ontop of the intake manifold that your tb bolts up to? if i ported the plenum and tb my self could i cause my car any damage? if done wrong? if so what could occur? __________________ sky 96 mustang gt:ram air, k&n, intake spacer, o\r x, flowmasters, pulleys, nitto drag radials, plugs, wires, 180 stat,

05-03-2003, 09:45 AM	#6
Badass_yellowGT Registered Member Join Date: Jun 2002 Location: Western,MA Posts: 254	yes it is the part the tb attaches to the only problem i could see is if you port it to much like said buy a used one and do it on that.thats what i`m doing __________________ Rice Haters Club Member #55 For My car Specs Click the Home page link http://www.badassyellowgt.50g.com/

05-02-2003, 07:02 PM	#5
biecomp Registered Member Join Date: Jan 2003 Location: NJ Posts: 12	I got a used on on e-bay to port it. You don't have to worry about messing up the one on the car and you can take your time with it. Check e-bay or your local junk yards for one and port that. Than do the swap. If everything works well , port the one you took off the car and sell it.

05-04-2003, 06:52 PM	#7
surfbeast Registered Member Join Date: Feb 2002 Location: Maryville,TN Posts: 415	I purchased a used T/B and plenum on E-Bay also and polished the plenum and T/B to a mirror finish. I also noticed that the inside of the plenum was really rough and had lots of slag hanging in it. I ported it as much as the tools I had allowed and polished it out. I put an intake spacer in ( $ 15, what the hell.. if it helps it helps) and hopefully the port job helped out. With all the rough edges and drag caused in the thing it had to help. Best of all it was free except for the cost of the dremel bits and my time. I polished my old plenum and sold it for $75 bucks! only pais $25 for the used one with the T/B! __________________ 98 GT / convertable -98 Saleen engine, Saleen appearance pkg. SHM cams,P&P NPI heads, and so much more!

05-08-2003, 10:19 PM	#8
TigerBravo Registered Member Join Date: May 2003 Location: Baton Rouge, LA Posts: 10	I read the same article in mm&ff and they specifically said that it was a mod you could do on the 99 & ^ gt. I was wondering if the same could be done on any 4.6 (96 & ^). I am going to be adding a sc to my 98 and that would definately be a plus to my set up.

05-09-2003, 10:51 AM	#9
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	I think that on pre-'99(?) cars the walls of the plenum are not as thick and don't allow you to remove enough material compared to the newer plenums, but you can put a ported '99+ plenum on your '96-'98. If you call Ben Alameda Racing there is a message saying that they don't take cores anymore because of all the 'unusable' cores they received. Because of this it now costs you $220 to buy one from them. __________________ Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s

05-12-2003, 03:39 PM	#11
ajcolv Registered Member Join Date: Oct 2002 Location: Utah Posts: 58	Does the 99+ upper fit the 96-98's without any issues? Is it basically a straight swap? __________________ -Aaron "Lita" 97 Mustang GT Vert -------------------------------------- k&n, air silencer removed, Magnapack cat-back, BBK o/r h-pipe, Ford red front calipers

05-12-2003, 06:01 PM	#12
surfbeast Registered Member Join Date: Feb 2002 Location: Maryville,TN Posts: 415	Yes it fits. Tha one I purchased was from a 2001. I ported it myself. Cost about $10 bucks. Also ported my old 98 plenum. I may not have done as good a job as the pros but mine was probably as good. It had to help, you would not believe what the inside of the plenum looks like . I figured it would be all smooth and clean, "NOT!". even if you clean it up a little it would have to help! __________________ 98 GT / convertable -98 Saleen engine, Saleen appearance pkg. SHM cams,P&P NPI heads, and so much more!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Safety Issue 64 - 70 Mustangs	Mach1 Cobra Jet	Classic Mustangs	20	07-11-2005 08:06 PM
Yellow Mustang Stampede TULSA OK August 17	stylin99	Ford Show & Go	2	11-09-2004 11:19 PM
t-5, is it the same in the 4 cylinder and V8	ex-lt1-guy	Windsor Power	12	03-03-2002 01:59 AM
89-Mustang pulling trailer -vs- 2000 Mustang	Five0	Stang Stories	7	04-01-2001 02:50 AM
Salaeen, Shelby, Cobra please define these for me.	Taqus	Blue Oval Lounge	3	01-17-2001 02:39 AM