![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Dec 2005
Posts: 14
|
![]() i just bought a set of mac ceramic headers for my 01 since then i have heard bad things about them hurting the engine i dont see how that cam happen but i thought i would ask. should i return them or will thay be ok to run. i bought mac because thay were easy to get is there a better header.
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Dec 2005
Posts: 14
|
![]() buy the way thay are long tube
|
![]() |
![]() |
![]() |
#3 |
5.7 < 5.0... and I failed math
Join Date: Jan 2006
Location: Mooresville, N.C.
Posts: 13
|
![]() Ok, I'm not going to be a smartazz about this, but who ever said that should be hit with a shovel. Not only does that not make sense, it's just plain silly. MAC makes great exhaust product, as does many other companies. Tell that guy to go jump off a bridge or something.
__________________
95' Mustang GT-S: Mac headers, off-road H, and cat back, 3.73, Mac fenderwell cold air, throttle body spacer, Mac under-drive pulleys, crane cam .530/.530,Professional products intake, 70mm TB, Tremec TKO500, Hurst short throw, UPR handle, Ford racing strut tower brace, Mickey Thompson ET's, broken stock axles Best ET: 8.53 @ 81 MPH Sponsored by Modular Madness Mooresville, N.C (704) 660-3464 |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Dec 2005
Posts: 14
|
![]() I guess years ago Mac had a problem with slag from the welds getting in to the egr system and scoring the cylinders but the problem has been corrected I guess I should have called Mac first thanks anyways
|
![]() |
![]() |
![]() |
#5 |
Huh? Whatcha said?
Join Date: Oct 2000
Location: Fayetteville, NC
Posts: 1,073
|
![]() First I have never heard of that. I agree that it is possible for the slag to get in there and mess things up, but that is not limited to just MAC. I wouldn't worry about it.
__________________
2003 GT White---STOLEN May you burn in hell whoever took it. Dumbazz didn't even get the good engine that was in the garage. |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Dec 2005
Posts: 14
|
![]() i starte dto install the l/t holly smoke what a project
|
![]() |
![]() |
![]() |
#7 |
Huh? Whatcha said?
Join Date: Oct 2000
Location: Fayetteville, NC
Posts: 1,073
|
![]() HA HA. You'll have that. Don't forget to lift the motor.
Enjoy. Post some pics when you get it done.
__________________
2003 GT White---STOLEN May you burn in hell whoever took it. Dumbazz didn't even get the good engine that was in the garage. |
![]() |
![]() |
![]() |
#8 |
13.3 @ 103
Join Date: May 2001
Location: Maryland
Posts: 253
|
![]() You are correct about prior problems with the quality of MAC headers. They used to have alot of problems with welds at the flanges. I would probably say that MAC has corrected that problem...don't worry about it.
__________________
Equipment by: Steeda C&L COMP CAMS FRPP MSD Bassani Magnaflow MAC ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Dec 2005
Posts: 14
|
![]() i just finshied the install i should have droped the k member in stead of lifting the engine wont do the again. lol. it sure runs and sounds good
|
![]() |
![]() |
![]() |
#10 |
Huh? Whatcha said?
Join Date: Oct 2000
Location: Fayetteville, NC
Posts: 1,073
|
![]() Long tubes.......*drool*
__________________
2003 GT White---STOLEN May you burn in hell whoever took it. Dumbazz didn't even get the good engine that was in the garage. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
2005 Ford Mustang JBA Silver Ceramic Coated Headers. GB | OnlineAutorama | Modular Madness | 0 | 07-14-2005 10:27 PM |
Buying new headers | TwiLighTBluEGT | Windsor Power | 4 | 04-23-2003 08:55 PM |
Anyone have problems with MAC headers?? | HiFlow5 0 | Windsor Power | 15 | 05-30-2002 08:30 AM |
Headers should I or shouldn't I....Need Advice Quick Please | Mustang_GT_90 | Windsor Power | 9 | 05-01-2002 01:16 PM |
BBK one-piece flange or MAC individual flange long tube headers. | Fox Body | Windsor Power | 10 | 04-03-2001 04:25 PM |