timing adjuster

Danbo · 11-15-1999, 12:12 PM

I tried the new Steeda timing adjuster
my car. I was disappointed with the results. I tried all kinds of combinations
of gap and advance. I finally went back to
10 degrees ( stock ) and it still did'nt
run well. I took it off. The car runs better
w/o it. Any one else have similar problems?

dan

------------------
'96 Cobra, Steeda G-Trac
Stage III Suspension, K&N
Filter,77mmPro-M,FMS Ceramic
Coated Headers,Bassini-X Pipe,
FMS Aluminum driveshaft,
FMS 3.73's, Cobra R's ,
Firestone SZ-50 275-40x17's,
Powerslot Rotors, Preformance Friction Z rated pads,
Steeda Tir-Ax, Schroth Restraints,
Kuhmo Victoracers(for the track).

Hammer · 11-16-1999, 08:27 PM

My personal feeling on this item is that the best results may occur from super-charged applications only... Just my opinion ;-)

Just how much did it set you back anyway?

------------------
98 GT
Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

Danbo · 11-18-1999, 12:21 AM

I agree, I think the best applicaton is on supercharged motors where you need to pull out timing.
It cost me $179. Now it's back in the box.
maybe I'll find someone else that wants it.
Dan

------------------
'96 Cobra, Steeda G-Trac
Stage III Suspension, K&N
Filter,77mmPro-M,FMS Ceramic
Coated Headers,Bassini-X Pipe,
FMS Aluminum driveshaft,
FMS 3.73's, Cobra R's ,
Firestone SZ-50 275-40x17's,
Powerslot Rotors, Preformance Friction Z rated pads,
Steeda Tir-Ax, Schroth Restraints,
Kuhmo Victoracers(for the track).

JStang · 11-18-1999, 07:07 PM

So if this timing adjuster doesn't work w/o a supercharged motor and there's no manual timing adjustment (from another post), then how can I adjust the timing on my 98GT?

--JStang

Danbo · 11-18-1999, 07:24 PM

I've talked to the folks at Steeda. they say that their Timing adjuster works. "It allows you to manually adjust the timing". The I had was detonation. Steeda says other folks have'nt had that problem. The only other way to alter the timing would be a costom burnt chip. Everything i've read on custonm chips
only showed improvements with superchargers.
So...I don't know what to try. Five more
Hp wasn't worth the effort it was taking to
get the Adjuster set up.
Dan

------------------
'96 Cobra, Steeda G-Trac
Stage III Suspension, K&N
Filter,77mmPro-M,FMS Ceramic
Coated Headers,Bassini-X Pipe,
FMS Aluminum driveshaft,
FMS 3.73's, Cobra R's ,
Firestone SZ-50 275-40x17's,
Powerslot Rotors, Preformance Friction Z rated pads,
(Track PF90 Compound pads),Steeda Tri-Ax,
Schroth Restraints,Kuhmo Victoracers(for the track)
Steeda Functional Wing.

kg2hk · 11-19-1999, 09:05 AM

Be careful with those timing adjusters! I read horror stories on corral.net - some guys were experiencing the same results and kept trying to tweak it and others must not have installed it correctly. Both ended up destroying the motor.

From what I heard, it's sounds like it's just not worth the headache (or risk) for a few HP.

------------------
99 Laser Red GT
Mods: 70mm TB, Level 10 Chip, FMS 3.73's, Sean Hyland Speedo Recalibration kit, Pro 5.0 Shifter, & Pro-M 77mm MAF.
DynoJet: 242HP/286 Lb/ft
Best 1/4: 13.839@99.1MPH on radials.

11-15-1999, 12:12 PM	#1
Danbo Registered Member Join Date: Jul 1999 Location: baltimore Posts: 99	timing adjuster I tried the new Steeda timing adjuster my car. I was disappointed with the results. I tried all kinds of combinations of gap and advance. I finally went back to 10 degrees ( stock ) and it still did'nt run well. I took it off. The car runs better w/o it. Any one else have similar problems? dan ------------------ '96 Cobra, Steeda G-Trac Stage III Suspension, K&N Filter,77mmPro-M,FMS Ceramic Coated Headers,Bassini-X Pipe, FMS Aluminum driveshaft, FMS 3.73's, Cobra R's , Firestone SZ-50 275-40x17's, Powerslot Rotors, Preformance Friction Z rated pads, Steeda Tir-Ax, Schroth Restraints, Kuhmo Victoracers(for the track).

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Steeda Timing Adjuster	XTheOwl	Modular Madness	5	06-06-2003 07:38 PM
Check engine light after steeda pullies / timing adjuster!! HELP!!	MineralGray02K	Modular Madness	1	09-29-2002 01:11 AM
AAAARGH! Steeda timing adjuster causing computer problems!!!	bark3rd	Modular Madness	1	06-04-2001 08:15 PM
Timing adjustment with Steeda adjuster	bark3rd	Modular Madness	5	05-17-2001 07:12 AM
Dyno results inside with timing adjuster installed	Mustang92	Modular Madness	7	02-20-2001 09:24 PM

11-16-1999, 08:27 PM	#2
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	My personal feeling on this item is that the best results may occur from super-charged applications only... Just my opinion ;-) Just how much did it set you back anyway? ------------------ 98 GT Dyno-Max cat-back exhaust, 3.73 gears, Steeda shifter, Ford Motorsport Underdrive pullies, 87mm MAF and Roush cold air kit...

11-18-1999, 12:21 AM	#3
Danbo Registered Member Join Date: Jul 1999 Location: baltimore Posts: 99	I agree, I think the best applicaton is on supercharged motors where you need to pull out timing. It cost me $179. Now it's back in the box. maybe I'll find someone else that wants it. Dan ------------------ '96 Cobra, Steeda G-Trac Stage III Suspension, K&N Filter,77mmPro-M,FMS Ceramic Coated Headers,Bassini-X Pipe, FMS Aluminum driveshaft, FMS 3.73's, Cobra R's , Firestone SZ-50 275-40x17's, Powerslot Rotors, Preformance Friction Z rated pads, Steeda Tir-Ax, Schroth Restraints, Kuhmo Victoracers(for the track).

11-18-1999, 07:07 PM	#4
JStang Registered Member Join Date: Oct 1998 Location: Mountain View, Ca 94040 Posts: 1	So if this timing adjuster doesn't work w/o a supercharged motor and there's no manual timing adjustment (from another post), then how can I adjust the timing on my 98GT? --JStang

11-18-1999, 07:24 PM	#5
Danbo Registered Member Join Date: Jul 1999 Location: baltimore Posts: 99	I've talked to the folks at Steeda. they say that their Timing adjuster works. "It allows you to manually adjust the timing". The I had was detonation. Steeda says other folks have'nt had that problem. The only other way to alter the timing would be a costom burnt chip. Everything i've read on custonm chips only showed improvements with superchargers. So...I don't know what to try. Five more Hp wasn't worth the effort it was taking to get the Adjuster set up. Dan ------------------ '96 Cobra, Steeda G-Trac Stage III Suspension, K&N Filter,77mmPro-M,FMS Ceramic Coated Headers,Bassini-X Pipe, FMS Aluminum driveshaft, FMS 3.73's, Cobra R's , Firestone SZ-50 275-40x17's, Powerslot Rotors, Preformance Friction Z rated pads, (Track PF90 Compound pads),Steeda Tri-Ax, Schroth Restraints,Kuhmo Victoracers(for the track) Steeda Functional Wing.

11-19-1999, 09:05 AM	#6
kg2hk Registered Member Join Date: Oct 1999 Location: Stony Point. NY Posts: 18	Be careful with those timing adjusters! I read horror stories on corral.net - some guys were experiencing the same results and kept trying to tweak it and others must not have installed it correctly. Both ended up destroying the motor. From what I heard, it's sounds like it's just not worth the headache (or risk) for a few HP. ------------------ 99 Laser Red GT Mods: 70mm TB, Level 10 Chip, FMS 3.73's, Sean Hyland Speedo Recalibration kit, Pro 5.0 Shifter, & Pro-M 77mm MAF. DynoJet: 242HP/286 Lb/ft Best 1/4: 13.839@99.1MPH on radials.