© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-14-2001, 03:13 PM | #1 |
Registered Member
Join Date: Aug 2001
Location: MIAMI, FLORIDA, USA
Posts: 50
|
Moroso? When Will It Open Again?
WELL, I KNOW THAT MOROSO IS CLOSING UP FOR THE WINTER, I HAVENT BEEN ABLE TO GET MY CAR READY TO TAKE TO THE TRACK after the newest mods..after leaveing nitrous and going vortech,and the pi head swap and 2000 gt intake manifold. I HAVE IT OVER AT THE SHOP DOWN IN MIAMI RIGHT NOW (SOUTH FLORIDA PERFORMANCE). WELL THEY ARE INSTALLING A DIABLO CHIP , 44 LBS FUEL INJECTORS AND, A NEW MASS AIR FLOW METER. ( my car still has the 19 lbs fuel injectors, no chip and stock air flow meter) well i have a little problem, i blew a steel head gasket last night.. I WAS HOPING TO GET MY CAR TO TAKE IT TO RUN IT AT TEST AND TUNE TODAY, BUT THAT WAS NEVER GOING TO HAPPEN.. SO IF ANY ONE HAS THE INFOON MOROSO, IT WOULD BE APPRECIATED.
__________________
1998 MUSTANG GT 4.6L /Convertible, Automatic. Flowmasters, JBA shorty headers chrome, X-Pipes custom made, 3.73 Gears FMS, 70MM fms T-BODY, VORTECH SQ-TRIM V2 supercharger (6 lbs), HKS SSQ Blow off valve, Aluminum custom made inlet pipe(gives 1lb. more of boost), 2000 Gt PI heads and cams Machine shop worked, 2000 gt intake manifold , W/BBK Filter, FMS 30 lbs fuel injectors, DIABLO sport chip, PRO-M 80mm, 6:1 FMU VORTECH, BBK Fuel Pump 255 lph, Excel 400 secondary fuel pump, 4-Point HOOKER HEADERS chrome roll bar, NEX Racing bucket seats(19 LBS PER SEAT), 5-Point harnesses, JE CERAMIC FORGED PISTONS & RINGS, MANLEY RODS, Srp pins, and The block was honed and worked in a machine shop, Mark Luton Racing Rear seat delete kit., Cobra Cowl 4" Hood, Saleen S351 wing, TYC tail lights... |
12-14-2001, 04:32 PM | #2 |
Drag Racer!
Join Date: Nov 1999
Location: Lake Worth, FL USA
Posts: 757
|
If you want just keep my email address handy for questions about Moroso since it's practically my second home at this point. Tonight is the last test and tune for the year. Sunday they have the outlaw street drags but there are no time slips so it doesn't do you much good unless you want to grudge race. The first test and tune for 2002 is January 9th so take your time getting your car back together and make sure it's right before you head out.
I'll be out there on the 9th for sure sporting a new exhaust and possibily new intake. Bill
__________________
2000 GT VRS O/R X, Dynomax Bullets, Steeda Pulleys, Pro-M 80MM, 4.30s, UPR Pro Series Suspension, UPR Tubular K-member, MAC Longtubes, Bullitt Intake, TKO, VT Engine Stage 1 NA Cams, SCT Tune. 285 RWHP/296 RWTQ 11.97 @ 113.20 M/M 100, 7085 www.uprproducts.com www.ponyexpressperformance.com www.modulardepot.com |
12-14-2001, 10:48 PM | #3 |
Registered Member
Join Date: Oct 2000
Location: Saxonburg, PA, USA
Posts: 236
|
Ok thats it I'm moving south to where the tracks are open year round.
I have to wait till Mar.7th to run test tune for the NMRA event
__________________
Ed.. My Mustangs webpage NMRA M/M 7222 2000 Mustang GT - 5 speed Race weight w/o driver 3086lbs, 3250 w/ driver Best 1/4mile run to date: 12.79@105.96, 60' 1.76sec.(10-27-02) Best MPH 106.03(10-27-02)4.10gears |
12-15-2001, 02:20 PM | #4 |
Registered Member
Join Date: Aug 2000
Location: Plymouth, MI
Posts: 254
|
The track here doesn't reopen until April 1st! 4 1/2 months with no drag racing....
|
12-17-2001, 11:11 AM | #5 | |
Drag Racer!
Join Date: Nov 1999
Location: Lake Worth, FL USA
Posts: 757
|
Quote:
I'll be at that event, see you out there... Bill |
|
12-17-2001, 07:04 PM | #6 |
Registered Member
Join Date: Oct 2000
Location: Saxonburg, PA, USA
Posts: 236
|
Good to hear. I will be running the Factory Stock class. Just found out my rear tire combo is legal, which took forever to finally get an answer. 275/50 on a 15x10.
Now to completly redo rearend with Eaton posi. 31spline axles, c-clip eliminators and 3.73's Install nice new suspension and I'll be all set By the way anyone have idea on what parts are needed to install a Tremec 3550TKO in a '00.
__________________
Ed.. My Mustangs webpage NMRA M/M 7222 2000 Mustang GT - 5 speed Race weight w/o driver 3086lbs, 3250 w/ driver Best 1/4mile run to date: 12.79@105.96, 60' 1.76sec.(10-27-02) Best MPH 106.03(10-27-02)4.10gears |
12-18-2001, 12:04 PM | #7 |
Drag Racer!
Join Date: Nov 1999
Location: Lake Worth, FL USA
Posts: 757
|
For the TKO you need a new shifter, clutch disk, bellhousing and possibly driveshaft.
Bill |
12-19-2001, 06:31 PM | #8 |
Registered Member
Join Date: Oct 2000
Location: Saxonburg, PA, USA
Posts: 236
|
That seems rather easy enough. I was figuring a centerforce clutch and pressure plate , lakewood bell housing along with the TKO.
Now to find out if crossmember will work with TKO or modify existing one.
__________________
Ed.. My Mustangs webpage NMRA M/M 7222 2000 Mustang GT - 5 speed Race weight w/o driver 3086lbs, 3250 w/ driver Best 1/4mile run to date: 12.79@105.96, 60' 1.76sec.(10-27-02) Best MPH 106.03(10-27-02)4.10gears |
01-03-2002, 05:52 PM | #9 |
Registered Member
Join Date: Aug 2001
Location: MIAMI, FLORIDA, USA
Posts: 50
|
thanks mustang 92 ill keep you in mind.
, i finally got the computer up and running again aftr two weeks, well i have bad news and good news, first i leaned my stang it had the small 19lbs injectors in it and the the vehicle was runing lean, i popped one of the pistons in the front of the block, i ordered today the forged je ceramic coated pistons 9.1 compression with the good pins and rings, and forged manley rods, this was some really expensive sh*t ...i said before that my car had me in a ditch, with the head swap and , now im in a giant whole, needless to say, this is running a high tab on my credit cards. i am honestley beggining to wish i never went the supercharger route , because of how expensive this route tuned out. iwill be selling alo of my original factory car parts on ebay. my seller name is xasiks107x,if yo guys just want to take a look and see, i may be selling a 2000 gt romeo block with the 98 heads, the block has a bent crank, and needs a new timing chain cover, i may sell my dry nos set up, with some never opened parts like, rmte bottle opener, and purge kit. thanks,hopefully ill be up ad running in time for BRADENTON, FL. NMRA...tony
__________________
1998 MUSTANG GT 4.6L /Convertible, Automatic. Flowmasters, JBA shorty headers chrome, X-Pipes custom made, 3.73 Gears FMS, 70MM fms T-BODY, VORTECH SQ-TRIM V2 supercharger (6 lbs), HKS SSQ Blow off valve, Aluminum custom made inlet pipe(gives 1lb. more of boost), 2000 Gt PI heads and cams Machine shop worked, 2000 gt intake manifold , W/BBK Filter, FMS 30 lbs fuel injectors, DIABLO sport chip, PRO-M 80mm, 6:1 FMU VORTECH, BBK Fuel Pump 255 lph, Excel 400 secondary fuel pump, 4-Point HOOKER HEADERS chrome roll bar, NEX Racing bucket seats(19 LBS PER SEAT), 5-Point harnesses, JE CERAMIC FORGED PISTONS & RINGS, MANLEY RODS, Srp pins, and The block was honed and worked in a machine shop, Mark Luton Racing Rear seat delete kit., Cobra Cowl 4" Hood, Saleen S351 wing, TYC tail lights... |
01-04-2002, 09:05 AM | #10 | |
Registered Member
Join Date: Jan 2002
Location: So. Florida
Posts: 22
|
Re: Moroso? When Will It Open Again?
Quote:
Regards, Jeff 90 GT 89 TTA 87 GN Last edited by SPower6; 01-04-2002 at 09:29 AM.. |
|
01-06-2002, 06:18 PM | #11 |
Registered Member
Join Date: Aug 2001
Location: MIAMI, FLORIDA, USA
Posts: 50
|
yes
i just heard from a couple of people down here at fuddruckers hangout that it will open mid february also for the repaving/resurfacing....thanks
__________________
1998 MUSTANG GT 4.6L /Convertible, Automatic. Flowmasters, JBA shorty headers chrome, X-Pipes custom made, 3.73 Gears FMS, 70MM fms T-BODY, VORTECH SQ-TRIM V2 supercharger (6 lbs), HKS SSQ Blow off valve, Aluminum custom made inlet pipe(gives 1lb. more of boost), 2000 Gt PI heads and cams Machine shop worked, 2000 gt intake manifold , W/BBK Filter, FMS 30 lbs fuel injectors, DIABLO sport chip, PRO-M 80mm, 6:1 FMU VORTECH, BBK Fuel Pump 255 lph, Excel 400 secondary fuel pump, 4-Point HOOKER HEADERS chrome roll bar, NEX Racing bucket seats(19 LBS PER SEAT), 5-Point harnesses, JE CERAMIC FORGED PISTONS & RINGS, MANLEY RODS, Srp pins, and The block was honed and worked in a machine shop, Mark Luton Racing Rear seat delete kit., Cobra Cowl 4" Hood, Saleen S351 wing, TYC tail lights... |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Putnam Park Open track Oct. 23rd & 24th | indiana dave | Corner Carvers Delight | 0 | 07-23-2004 08:22 PM |
door won't open??!! | Simi Stang | Windsor Power | 7 | 09-23-2002 11:28 AM |
posi or open?? | 66StangGuy | Classic Mustangs | 7 | 05-25-2002 11:27 PM |
Passenger door wont open | jason347lx | Windsor Power | 3 | 01-23-2002 09:44 PM |
carb sticks wide open on '67 289 2V | DADS67 | Classic Mustangs | 3 | 10-24-1999 11:48 PM |