![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() this past weekend
me and 2 friends installed my longtube headers I have not got on it yet to see how they feel im going to get a few heat cycls. done first and then recheck the bolts and I hope to get to the track in the next 2 weeks to see if there were any gains and as soon as I do I will let you guys know
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
![]() |
![]() |
![]() |
#2 |
Addict
Join Date: Nov 2003
Location: chicopee, Ma.
Posts: 82
|
![]() im going to be doing the same thing in a few weeks ... any little tricks or things to look out for when raising the engine, or anywhere else?
__________________
'01 Roush Stage 3 |
![]() |
![]() |
![]() |
#3 |
College Stanger
Join Date: May 1999
Location: Aiken,south carolina, usa
Posts: 1,097
|
![]() What LT headers did you get?
__________________
2003 Sonic Blue Cobra |
![]() |
![]() |
![]() |
#4 | |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() Quote:
there is no rear tricks it just takes time go over to www.modulardepot.com and bill putman has a write up on the header install
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
|
![]() |
![]() |
![]() |
#5 |
Addict
Join Date: Nov 2003
Location: chicopee, Ma.
Posts: 82
|
![]() bbk
__________________
'01 Roush Stage 3 |
![]() |
![]() |
![]() |
#6 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
![]() We did longtubes on my car and a friend's car without dropping the k-member. Unfortunately the real pain is getting the bolts on the passenger side started and there are no tricks for this other than raising the motor. Having a friend with very small hands helps. When you raise the motor you just need to make sure that you are not hitting anything on the top side as you lift it.
The top starter bolt is kinda tough too. I used a combination of extensions and a swivel to get to it.
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
![]() |
![]() |
![]() |
#7 |
Addict
Join Date: Nov 2003
Location: chicopee, Ma.
Posts: 82
|
![]() thanks for the info. i just visited the site. a TON of info, much appreciated
__________________
'01 Roush Stage 3 |
![]() |
![]() |
![]() |
#8 | |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() Quote:
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
SVO Shorty Headers 1-5/8 Question | stangposse | Windsor Power | 0 | 08-07-2003 12:48 PM |
Buying new headers | TwiLighTBluEGT | Windsor Power | 4 | 04-23-2003 08:55 PM |
Anyone have problems with MAC headers?? | HiFlow5 0 | Windsor Power | 15 | 05-30-2002 08:30 AM |
Headers should I or shouldn't I....Need Advice Quick Please | Mustang_GT_90 | Windsor Power | 9 | 05-01-2002 01:16 PM |
BBK one-piece flange or MAC individual flange long tube headers. | Fox Body | Windsor Power | 10 | 04-03-2001 04:25 PM |