roll control 2001 gt

jwmustangin · 04-14-2002, 05:16 PM

Wassuup!
Seems that nobody can answer the thread I posted earlier this week about how to put a line lock on 2001 gt with ABS and traction control.

I've thought of two ways on how to do it.
1. Buy two line lock kits and install them after the ABS module in the brake line with one on the left front wheel and the other on the right front wheel. Then you would have to wire the two line locks in series to a single switch inside of the car.

2. Buy one line lock kit and install it in the brake line for the front brakes between the master cylinder and the ABS module. This of course would require back bleeding (feeding brake fluid into the system from the bleeder valve at one of the front wheels' brake caliper instead of feeding the fluid in through the master cylinder). This is required so that you prevent an air pocket from getting into the ABS module.

So, what do all of you hot rod stangers think. I think that I have stumped a few of you. If any body knows anyone that might know the answer to my problem, I would greatly appreciate it if they would respond to my thread!
Later,
Jeff Williams (jwmustangin)

SLOW 97 · 04-17-2002, 09:10 AM

You're in luck! Paul's High Performance now has a line lock especially for newer 'Stangs with ABS. Previously you couldn't use roll with anti lok brakes.

96GTPRT · 04-17-2002, 05:31 PM

Yeah, Slow 97 is right, Pauls does have one, check out the June 2002 5.0 Mustang magazine (pg 183) for all the details. Its about $344.95 check out Pauls website too, www.paulshp.com. They are nice people.

04-14-2002, 05:16 PM	#1
jwmustangin Registered Member Join Date: Apr 2002 Location: lynchburg, va Posts: 18	roll control 2001 gt Wassuup! Seems that nobody can answer the thread I posted earlier this week about how to put a line lock on 2001 gt with ABS and traction control. I've thought of two ways on how to do it. 1. Buy two line lock kits and install them after the ABS module in the brake line with one on the left front wheel and the other on the right front wheel. Then you would have to wire the two line locks in series to a single switch inside of the car. 2. Buy one line lock kit and install it in the brake line for the front brakes between the master cylinder and the ABS module. This of course would require back bleeding (feeding brake fluid into the system from the bleeder valve at one of the front wheels' brake caliper instead of feeding the fluid in through the master cylinder). This is required so that you prevent an air pocket from getting into the ABS module. So, what do all of you hot rod stangers think. I think that I have stumped a few of you. If any body knows anyone that might know the answer to my problem, I would greatly appreciate it if they would respond to my thread! Later, Jeff Williams (jwmustangin)

04-17-2002, 09:10 AM	#2
SLOW 97 Registered Member Join Date: Feb 2002 Location: Arlington Heights,IL Posts: 231	You're in luck! Paul's High Performance now has a line lock especially for newer 'Stangs with ABS. Previously you couldn't use roll with anti lok brakes. __________________ '97 Laser Red GT Coupe Stock 2V (Pulled Silencer) 4R70W Automatic Ripped off a BLISTERING 15.37@90MPH With a 2.21 60ft Just Installed- K&N Air Filter Coming Soon...... -4.10's -Flowmaster A/T or Magnapack Cat-Back

04-17-2002, 05:31 PM	#3
96GTPRT Registered Member Join Date: Apr 2002 Location: Naperville, IL Posts: 69	Yeah, Slow 97 is right, Pauls does have one, check out the June 2002 5.0 Mustang magazine (pg 183) for all the details. Its about $344.95 check out Pauls website too, www.paulshp.com. They are nice people. __________________ 96GTPRT: '96 Laser Red Tinted Mustang GT Convertible. (tan top). Flowmaster cat-back, Bassani X-pipe w/ cats, K&N FIPK, Hypertech 160* t-stat, MSD wires, Bosch plugs, Performance Distributors coil packs, FRPP 70mm throttle body, C&L 87mm mass air. Kenny Brown Super subs, 3.73's, BFGoodrich Comp T/A's Civic...its whats for dinner. Don't ever pull a ricer fly-by!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2001 GT Paint Job	2001GTPEWTER	Built Ford Tough	0	09-05-2004 01:50 PM
2001 GT Work	2001GTPEWTER	Windsor Power	3	08-30-2004 02:07 PM
2001 GT goes down, so does modded WRX.	Steeda90GT	Stang Stories	4	09-04-2002 02:05 PM
4.10's on 2001 GT?	wickedgt	Modular Madness	15	05-09-2002 11:40 AM
2001 GT Knock When Cold	MHarmon	Modular Madness	8	02-28-2002 10:19 PM