Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
08-22-2005, 05:34 PM
|
#1 |
|
Registered Member
Join Date: Jun 2005
Posts: 8
|
jet hot header
hi guys
my friend have mustang 00 gt and he have installed a jet hot headers with xpipe but after the installation when start up the engine he have a strong vibration (you feel it in the steering wheel and transmission) is this from the headers and it`s ok or there is something wrong |
|
|
|
08-23-2005, 05:08 AM
|
#2 |
|
Registered Member
Join Date: Jun 2005
Posts: 8
|
Re: jet hot header
no answer ????
|
|
|
|
|
08-23-2005, 12:23 PM
|
#3 |
|
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
Re: jet hot header
Installing headers and x-pipe generally shouldn't cause any extra vibrations. Is it because the engine is running rough after the install? It's possible that the driver's side header is touching the steering shaft and causing part of it. The X-pipe does hang from the tranny cross member too and it's all connected to the motor, so it sounds like all of it could be from the engine running rough now.
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
|
|
|
|
08-24-2005, 07:17 AM
|
#4 |
|
Moderator
Join Date: Aug 2000
Location: Milan, OH
Posts: 2,699
|
Re: jet hot header
Did you re-tighten the motor mounts?
__________________
Jeff Chambers 1990 Mustang GT 10.032 Seconds / 137.5 MPH 14-time Street Warrior World Record Setter CRT Performance 2001 Tropic Green Mustang GT - 12.181 / 113.2 MPH 2002 Ford F-250 Crew Cab 7.3l Power Stroke - 17.41@77.2 "There's nothing boring about a small block automatic shifting gears at 9400 rpm!" |
|
|
|
|
08-27-2005, 05:15 PM
|
#5 |
|
Registered Member
Join Date: Jun 2005
Posts: 8
|
Re: jet hot header
yes i did re-tighten the motor mounts
|
|
|
|
|
08-27-2005, 05:16 PM
|
#6 |
|
Registered Member
Join Date: Jun 2005
Posts: 8
|
Re: jet hot header
yes i did ......................................
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Broken Header Stud (header to Hpipe) | PeTr0 | Windsor Power | 3 | 01-01-2005 06:34 PM |
| 1 3/4 long tube header install. | Dark_5.0 | Windsor Power | 1 | 08-05-2004 01:51 PM |
| Header and Exhaust Installation | 1991GT | Windsor Power | 4 | 12-03-2002 11:17 PM |
| Header Panel....ie,,,nose cone/front bumper cover | ScrubTek | Appearance & Detailing | 0 | 08-23-2002 10:29 PM |
| Header Gasket Help Needed | Phillip Long | Windsor Power | 5 | 05-03-2002 01:59 PM |