Ignition Module

mustangLX92 · 06-29-2001, 10:58 AM

What is the average cost of a new ignition module. Is the installation hard?

88conv · 06-29-2001, 11:18 AM

25 to $30- Autozone- they sell a ford ignition wrench which helped alot. Unscrew two screws. Put grease on back of new module(comes with it). Screw back on. Hope this helps.

SPEEDY88 · 06-30-2001, 11:24 PM

hey you can also use a 5.5mm nut driver. I just recently replaced mine, it wasn't hard at all. While you are at it you can buy a high performance module at almost the same price!! hope this helps

------------------
88GT-Bassani X-pipe,Two chamber flowmasters,3:73 gears, King Cobra clutch, Steeda clutch quadrant, pro 5.0, K&N, Hypertech chip, Underdrive Pulleys,High Volume oil pump....ALL POWERED BY MY FOOT!!!

89LXNB · 07-05-2001, 05:18 AM

When this module goes, your car wont run at all. If you want to be certain that the module is functioning correctly you can test it. You will need an ohmeter or you can have the auto parts store test it for you. 5.5 is the correct size of bolt but you may need to either counter bore the module slightly to accomodate the socket, or grind down the od of the socket so that it seats properly into the module.

06-29-2001, 10:58 AM	#1
mustangLX92 Registered Member Join Date: May 2001 Location: Maryland Posts: 138	Ignition Module What is the average cost of a new ignition module. Is the installation hard?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
TFI module vs Ignition module	teallighting	Windsor Power	1	03-21-2004 03:38 AM
Best Ignition module and Coil?	88fivepointoh	Windsor Power	2	03-02-2003 01:23 PM
Ignition module	bobtodd	Windsor Power	9	08-18-2002 07:12 PM
Fuel pump, Ignition module or something else?	MattwantsSpeed	Windsor Power	16	07-07-2002 08:38 PM
Best place to mount an ignition module?	Blue Beast	Windsor Power	4	03-16-2002 01:19 PM

06-29-2001, 11:18 AM	#2
88conv Registered Member Join Date: May 2001 Location: Athens,Ga. Posts: 26	25 to $30- Autozone- they sell a ford ignition wrench which helped alot. Unscrew two screws. Put grease on back of new module(comes with it). Screw back on. Hope this helps.

06-30-2001, 11:24 PM	#3
SPEEDY88 Registered Member Join Date: Oct 1999 Location: TEXAS Posts: 110	hey you can also use a 5.5mm nut driver. I just recently replaced mine, it wasn't hard at all. While you are at it you can buy a high performance module at almost the same price!! hope this helps ------------------ 88GT-Bassani X-pipe,Two chamber flowmasters,3:73 gears, King Cobra clutch, Steeda clutch quadrant, pro 5.0, K&N, Hypertech chip, Underdrive Pulleys,High Volume oil pump....ALL POWERED BY MY FOOT!!!

07-05-2001, 05:18 AM	#4
89LXNB Registered Member Join Date: Jul 2000 Location: San Jose CA Posts: 149	When this module goes, your car wont run at all. If you want to be certain that the module is functioning correctly you can test it. You will need an ohmeter or you can have the auto parts store test it for you. 5.5 is the correct size of bolt but you may need to either counter bore the module slightly to accomodate the socket, or grind down the od of the socket so that it seats properly into the module.