Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
05-30-2000, 06:18 PM
|
#1 |
|
Registered Member
Join Date: Jan 2000
Location: Ypsilanti, Michigan, USA
Posts: 25
|
Brake pads
What brand and type of brake pads would ya'll recomend for a 96 Cobra doing drivers ed and open track events and mimimal street time?
------------------ '96 Mystic Cobra, K&N, 4.10 Gears Steeda Tri-Ax HPM Lower Control Arms Castor Camber Plates and Panhard Bar |
|
|
|
05-31-2000, 11:25 AM
|
#2 |
|
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
Performance Friction "Z" pads. These are agressive street pads. I ran these on my stock 89 Mustang brakes. I thought they were a HUGE improvement over the stock pads. They didnt fade all too quickly, and when they did, I could back off, let the cooling ducts do their job, and the pads would come back. These pads were like $60 with a lifetime warranty (i.e. Free pads every summer).
Right now I run Performance Friction 90 Compound pads on my M2300K Cobra brakes. These are like $200+ for the fronts (ouch). THey are a GREAT track pad, but not any good on the street. ------------------ Darius Rudis Roadracer: Home built t-arm/panhard suspension powered by an S-trimmed motor :-) My Mustang Page |
|
|
|
|
05-31-2000, 06:48 PM
|
#3 |
|
Registered Member
Join Date: Jan 2000
Location: Ypsilanti, Michigan, USA
Posts: 25
|
Thanks Darius! I think I will try them, I really don't want to send $200 on pads that are only good "racing"! Do I need to change the rears also?
|
|
|
|
|
06-01-2000, 02:45 PM
|
#4 |
|
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
Look into the www.maximummotorsports.com brake pad "kit". Havnt used it, but look promising. I simply used PF Z pads on all fronts, that was enough.
------------------ Darius Rudis Roadracer: Home built t-arm/panhard suspension powered by an S-trimmed motor :-) My Mustang Page |
|
|
|
|
06-02-2000, 06:48 AM
|
#5 |
|
Registered Member
Join Date: Jan 2000
Location: Ypsilanti, Michigan, USA
Posts: 25
|
Darius, Great thanks for the help. This looks exactly like what I had in mind. Streetable yet adequate for my drivers ed track time. Thanks again!!
------------------ '96 Mystic Cobra, K&N, 4.10 Gears Steeda Tri-Ax HPM Lower Control Arms Castor Camber Plates and Panhard Bar |
|
|
|
 |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Mustang 2000 Rear Disk Brake Repairs | JerryR | Modular Madness | 11 | 10-22-2002 09:08 AM |
| Replacing Brake Pads on 96 F150 | jimberg | Built Ford Tough | 2 | 08-26-2002 04:01 PM |
| Porcelain Brake Pads! | gtsr515 | Windsor Power | 11 | 05-06-2002 10:02 AM |
| brake pads? | delrrex | Windsor Power | 5 | 06-30-2001 12:01 PM |
| How long does 98 Cobra brake pads last? | fastcobra | Modular Madness | 3 | 06-11-2000 01:20 AM |